The paper presents the results of numerical modelling of the forging process of magnesium alloy ingots on a hydraulic press with the use of flat and shaped anvils. The use of shaped (rhombic-trapezoid) anvils will affect the uniform distribution of temperature and strain intensity in the entire volume of the forging, causing a number of forging passes, which in consequence will reduce the costs of the blank manufacturing process. However, higher values of the strain intensity were obtained during the deformation of the material in flat anvils. The purpose of the research was to propose assumptions for forging technology of producing a blank from AZ91 alloy with the use of flat and shaped anvils. Numerical examination for AZ91 magnesium alloy was carried out using the Forge^®NxT commercial software. The rheological properties of the investigated alloy were determined on the basis of uniaxial compression tests carried out in the Gleeble 3800 metallurgical simulation system. The numerical analysis of the process of forging AZ91 alloy ingots on a press was conducted in the temperature range of 200–400 °C and at several forging passes.

Among non-destructive testing methods, a group dedicated to the assessment of the state of residual stresses can be distinguished. The method of measuring residual stresses using the Barkhausen noise method has many advantages, as evidenced by the number of publications. The residual stresses in metal products are important for the further processing of such metal, such as laser cutting or bending. The results presented in this work are of an experimental nature, and the presented method of calibration of measuring heads shows how various research techniques can be used to correlate results. The research was carried out for structural steel due to the market share of this type of steel. The method can be used to measure the residual stresses in ferromagnetic metal products in order to assess their directions and quantify them. A prerequisite for the use of this measurement method is that the amplitude and geometry of the Barkhausen noise are adequately correlated to the specific values of the state of stress depending on the tested steel grade or other metals. In this study, a method for calibrating measuring sensors for the residual stress measurements is presented, as developed by the authors. The method involved conducting bending tests in both numerical modeling and experimental tests. During the bending tests, changes in the magnetic field (Barkhausen noise waveform) were recorded, taking into account the state of elastic stresses. Correlating the results of the numerical calculations and Barkhausen noise measurements made it possible to determine the quantitative values of the residual stresses in the steel sheets. Thanks to the method used, very accurate measurement is possible, and the obtained results are repeatable.

This paper presents the results of research on the determination of the influence of kinetic asymmetry of work rolls on structural changes in hot-rolled bimetallic sheet metals. The tests were conducted on bimetallic samples composed of materials 10CrMo9-10 + X2CrNiMo17-12-2. The scope of the research included a comparative analysis for two cooling variants: I in water (freezing the structure immediately after rolling) and II for cooling in air. The research conducted showed that the introduction of asymmetric conditions to the rolling process results in a greater grain fragmentation in the so-called hard layer and does not have a negative effect on microstructural changes in the soft layer.

The article presents the results of experimental studies on the symmetrical and asymmetrical rolling process of composite laminate sheets consisting of difficult-to-deform Ti and Ni materials. Composite sheets joined by explosive welding were used for the tests. The aim of the research was to determine the impact of plastic shaping conditions in the rolling process on the quality and selected functional properties of the materials constituting the layered composite. The rolling process was carried out cold on a duo laboratory rolling mill with a roll diameter of 300 mm. During the rolling process, the influence of the rolling process conditions on the distribution of metal pressure forces on the rolls was determined, as well as the shear strength and microstructural studies of the joint area of the layered composites. As part of the conducted considerations, residual stress tests were carried out using the Barkhausen noise method. The scientific aim of the presented work was to determine the optimal conditions for the plastic processing of multi-layer Ti-Ni sheets. The results presented in the work allowed for determining the most favorable conditions for the rolling process.

This paper presents the results of numerical tests of the process of forging magnesium alloy ingots (AZ91) on a hydraulic press with the use of flat and proprietary shaped anvils. The analysis of the hydrostatic pressure distribution and the deformation intensity was carried out. It is one of the elements used for determining the assumptions for the technology of forging to obtain a semi-finished product from the AZ91 alloy with good strength properties. The aim of the research was to reduce the number of forging passes, which will shorten the operation time and reduce the product manufacturing costs. Numerical tests of the AZ91 magnesium alloy were carried out using commercial Forge^®NxT software.

The aim of this research was to select parameters for the roll pre-leveler to provide sheet metal waviness reduction after unwinding from the coil. Straightening parameters were selected based on the results of numerical simulations with the use of an FEM-based computer program. The material used for research was a hot-rolled sheet metal of grade S235JR + AR with a thickness of 3 mm and width of 1500 mm after unwinding from the coil. A mathematical model was developed to determine straightening roll arrangements in the pre-leveler. It enabled roll arrangement selection and a straightening scheme to be elaborated. The model’s innovative feature was conducting straightening numerical simulations for the real sheet metal geometric models obtained as a result of 3D laser scanning, which increased the accuracy of the numerical calculations.