Petr Jilek

Dr. Petr Jilek

orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 January 2021 in Coatings
Verified
Journal Article
Open access
PDF file
MSMarie Sejkorová
Marie Sejkorová
IHIvana Hurtová
Ivana Hurtová
PJPetr Jilek
Petr Jilek
MNMartin Novák
Martin Novák
OVOndřej Voltr
Ondřej Voltr
Internal combustion engine lubrication is essential for unwanted energy and material losses. As part of the experimental work, the lubricity of both new and worn motor oils of Society of Automotive Engineers (SAE) 15W-40 and SAE 10W-40 with different American Petroleum Institute (API) performance classifications, which were taken from various motor trains during maintenance or oil change, was assessed. A total of sixteen lubricant samples were evaluated. Lubricity, i.e., the load capacity of the lubricating film, was evaluated on the basis of the Reichert test. Viscosity, as one of the most important parameters of lubricants, was evaluated by the Stabinger Viscometer. Chemical degradation of motor oils (oxidation, nitration, sulfation), contamination of oils with fuel, soot, water, and loss of antioxidant zinc dialkyldithiophosphate (ZDDP) were monitored by Fourier-transform infrared (FTIR) spectroscopy. Of the fresh motor oils, OMV 10W-40 API SL/CF motor oil had the best lubricity. URANIA LD 15W-40 API CI-4 and M7ADS V 15W-40 API CI-4 CH-4/SL oils showed similar lubricity. M7ADS III 15W-40 API CF-4/SG motor oil showed the highest wear of wear surface, i.e., the lowest lubricity, of the tested new motor oils. Correlation analysis of the experimental data confirmed that the fuel content penetrated the motor oils significantly negatively correlates with the viscosity (R = −0.87). The low water contamination in motor oil does not cause a significant negative effect on lubricity. A significant correlation between the oxidation, nitration, and sulfation products of chemical degradation of the tested oils was confirmed (R ≥ 0.90). These degradation products improve lubricity due to their polarity, i.e., they have caused better lubricity of worn oils compared to new motor oils. Even the depletion of the antioxidant ZDDP did not affect the reduction in lubricity and anti-abrasion properties of chemically degraded motor oils. The experimental results of testing of worn motor oils taken from motor trains showed that current motor oils have excellent lubricity, which they maintain throughout their life.

23 June 2022 in Applied Sciences
Verified
Journal Article
Open access
PDF file
STSławomir Tarkowski
Sławomir Tarkowski
ANAleksander Nieoczym
Aleksander Nieoczym
Jacek CabanJacek Caban
Jacek Caban
PJPetr Jilek
Petr Jilek
MSMarie Sejkorová
Marie Sejkorová
The article presents the results of simulations using the finite element method (FEM) aimed at examining the extent of damage to the wheel rim as a result of hitting an obstacle. The obtained results can be used as comparative data during the performance of expert opinions to give an answer as to how the damage occurred. The data obtained from the FEM simulation can also be used in the process of geometric optimization of the rim, which aims to obtain a rim resistant to this type of damage.

31 December 2021 in Applied Sciences
Verified
Journal Article
Open access
PDF file
PJPetr Jilek
Petr Jilek
JBJan Berg
Jan Berg
BTBaurice Sylvain Sadjiep Tchuigwa
Baurice Sylvain Sadjiep Tchuigwa
This paper deals with the optimization of the crossbars, parts of the existing frame of the experimental system of the Alternative SkidCar. This part plays a crucial role and is designed to enable and ensure reduced adhesion conditions between the vehicle and the road. To this end, its optimization targeted here is performed using both analytical calculations and simulations in MSC Adams software, wherein the loading forces and boundary conditions on the frame support wheels are obtained considering the static conditions, as well as the change of the direction of travel. The least favourable load observed was used, later on, as the input value for the strength analysis of the frame. The analysis was performed using the finite element method (FEM) in SolidWorks. Based on the linear and nonlinear analyses performed, the course of stress on the frame arms and critical points with the highest stress concentration were determined. Subsequently, according to the results obtained, a new design for the current frame was proposed and, thereby, warrants greater rigidity, stability and strength to the entire structure, while reducing its weight and maximizing the potential of the selected material. The benefit of the current contribution lies in the optimization of the current frame shape, in terms of the position of weld joints, the location of the reinforcements and the thickness of the material used.

30 June 2023 in The Archives of Automotive Engineering - Archiwum Motoryzacji
Verified
Journal Article
Open access
PJPetr Jilek
Petr Jilek
This article deals with the development and proposal to increase the application of equipment for measuring the adhesion force between the road and the road vehicle. The device enabling the adhesion force measurement of a rotating vehicle wheel is called a dynamic adhesor. The actual position of...

31 May 2021 in International Journal of Automotive Technology
Verified
Journal Article
Closed access
PDF file
PJPetr Jilek
Petr Jilek
JNJan Němec
Jan Němec

27 February 2020 in Acta Universitatis Agriculturae et Silviculturae Mendelianae Brunensis
Verified
Journal Article
Open access
PDF file
PJPetr Jilek
Petr Jilek
JNJan Němec
Jan Němec
Acta Universitatis Agriculturae et Silviculturae Mendelianae Brunensis, the scientific journal of the Mendel University in Brno, Czech Republic