Ondřej Voltr

Mr. Ondřej Voltr


Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 January 2021 in Coatings
Verified
Journal Article
Open access
PDF file
MSMarie Sejkorová
Marie Sejkorová
IHIvana Hurtová
Ivana Hurtová
PJPetr Jilek
Petr Jilek
MNMartin Novák
Martin Novák
OVOndřej Voltr
Ondřej Voltr
Internal combustion engine lubrication is essential for unwanted energy and material losses. As part of the experimental work, the lubricity of both new and worn motor oils of Society of Automotive Engineers (SAE) 15W-40 and SAE 10W-40 with different American Petroleum Institute (API) performance classifications, which were taken from various motor trains during maintenance or oil change, was assessed. A total of sixteen lubricant samples were evaluated. Lubricity, i.e., the load capacity of the lubricating film, was evaluated on the basis of the Reichert test. Viscosity, as one of the most important parameters of lubricants, was evaluated by the Stabinger Viscometer. Chemical degradation of motor oils (oxidation, nitration, sulfation), contamination of oils with fuel, soot, water, and loss of antioxidant zinc dialkyldithiophosphate (ZDDP) were monitored by Fourier-transform infrared (FTIR) spectroscopy. Of the fresh motor oils, OMV 10W-40 API SL/CF motor oil had the best lubricity. URANIA LD 15W-40 API CI-4 and M7ADS V 15W-40 API CI-4 CH-4/SL oils showed similar lubricity. M7ADS III 15W-40 API CF-4/SG motor oil showed the highest wear of wear surface, i.e., the lowest lubricity, of the tested new motor oils. Correlation analysis of the experimental data confirmed that the fuel content penetrated the motor oils significantly negatively correlates with the viscosity (R = −0.87). The low water contamination in motor oil does not cause a significant negative effect on lubricity. A significant correlation between the oxidation, nitration, and sulfation products of chemical degradation of the tested oils was confirmed (R ≥ 0.90). These degradation products improve lubricity due to their polarity, i.e., they have caused better lubricity of worn oils compared to new motor oils. Even the depletion of the antioxidant ZDDP did not affect the reduction in lubricity and anti-abrasion properties of chemically degraded motor oils. The experimental results of testing of worn motor oils taken from motor trains showed that current motor oils have excellent lubricity, which they maintain throughout their life.

23 April 2021 in Applied Sciences
Verified
Journal Article
Open access
PDF file
MSMarie Sejkorová
Marie Sejkorová
MKMarian Kučera
Marian Kučera
IHIvana Hurtová
Ivana Hurtová
OVOndřej Voltr
Ondřej Voltr
Viscosity is considered to be a key factor in the quality of lubrication by oil and engine manufacturers and is therefore one of the most monitored parameters of lubricants. FTIR (Fourier-transform infrared) spectrometry in combination with Partial Least Squares (PLS) and Principal Component Regression (PCR) was therefore proposed and tested as an alternative to the standardized method for determining the kinematic viscosity at 100 °C with an Ubbelohde capillary viscometer (CSN EN ISO 3104) of worn-out motor oil grade SAE 15W-40. The FTIR-PLS model in the spectral region of 1750–650 cm−1 with modification of the spectra by the second derivative proved to be the most suitable. A significant dependence of R = 0.95 was achieved between the viscosity values of 190 samples of worn-out motor oils, which were determined by a standardized laboratory method, and the values predicted by the FTIR-PLS model. The Root Mean Square Error of Calibration (RMSEC) parameter reached 0.148 mm2s−1 and the Root Mean Square Error of Prediction (RMSEP) parameter reached 0.190 mm2s−1. The proposed method for determining the kinematic viscosity at 100 °C by the FTIR-PLS model is faster compared to the determination according to the CSN EN ISO 3104 standard, requires a smaller amount of oil sample for analysis and produces less waste chemicals.

30 September 2021 in The Archives of Automotive Engineering - Archiwum Motoryzacji
Verified
Journal Article
Open access
Jacek CabanJacek Caban
Jacek Caban
OVOndřej Voltr
Ondřej Voltr
During the operation of vehicles, their operational parameters change, which is related to the influence of working factors, the current situation on the road and its capacity, as well as the wear processes of the vehicle components. Improving the operational and ecological properties of motor vehicles, taking into account technical, legal and operational factors, is a constantly important issue. The article presents selected test results of a vehicle used in the eco-driving technique in urban traffic. The main objective of the study was to verify the possibility of limiting intensive braking and the number of braking thanks to the use of eco-driving. Limitations of intensive braking allow extending the service life of the friction elements of the braking system. The research was carried out on the so-called routine route from work to home in a selected area of the city of Lublin in south-eastern Poland. The obtained research results focus on the influence of selected driving parameters, such as: mileage, road characteristics, number of vehicle stops, number of vehicle stops at intersections and in front of pedestrian crossings, depending on the driving style. The analysis of the results shows the benefits of eco-driving in city traffic.