Analysis of geophysical borehole data can often be hampered by too much information and noise in the trace leading to subjective interpretation of layer boundaries. Wavelet analysis of borehole data has provided an effective way of mitigating noise and delineating relevant boundaries. We extend wavelet analysis by providing a complete set of code and functions that will objectively block a geophysical trace based on a derivative operator algorithm that searches for inflection points in the bore log. Layer boundaries detected from the operator output are traced back to a zero-width operator so that boundaries are consistently and objectively detected. Layers are then classified based on importance and analysis is completed by selecting either total number of layers, a portion of the total number of layers, selection of minimum layer thickness, or layers detected by a specified minimum operator width. We demonstrate the effectiveness of the layer blocking technique by applying it to a case study for alluvial aquifer detection in the Gascoyne River area of Western Australia.
The noninvasive detection and characterization of subsurface aquifer structures demands geophysical techniques. Surface nuclear magnetic resonance (SNMR) is the only technique that is directly sensitive to hydrogen protons and, therefore, allows for unambiguous detection of subsurface water. Traditionally, SNMR utilizes large surface coils for both transmitting excitation pulses and recording the groundwater response. Recorded data are thus a voltage induced by the time derivative of the secondary magnetic field. For the first time, we demonstrate that the secondary magnetic field in a SNMR experiment can be directly detected using a superconducting quantum interference device magnetometer. Conducting measurements at a test site in Germany, we demonstrate not only the ability to detect SNMR signals on the order of femtoTesla but also we are able to satisfy the observed data by inverse modeling. This is expected to open up completely new applications for this exciting technology.
Bird attitudes, with roll, pitch, and yaw angles, are required for modeling the measured electromagnetic response of the earth. Global Positioning System (GPS) antennas can be used in airborne electromagnetic (AEM) systems to monitor airborne platform attitude and bird maneuver. We have found evidence from photographic sequences that four GPS antennas, three on the bird and one on the aircraft, generally are adequate for angular and altitude geometry control. The mounting system for the bird frame introduces vibration noise. We have developed a model that predicts bird maneuver from the use of GPS antennas already present during routine airborne surveys. The bird motion, whether inline or crossline, is modeled from the difference between the aircraft location and the mean location of the bird. This also accurately predicts the roll of the bird when an inline yoke mounting is used. The minimum number of GPS antennas required to monitor the motion of a cylindrical electromagnetic (EM) bird typical of frequency-domain systems is two, one on the aircraft and one on the bird. We have defined optimum locations of GPS antennas to enable geometric monitoring of towed-bird systems. The findings suggest that the bird be mounted with two aerodynamically efficient GPS antennas, one on the nose and one on the tail. This enables the measurement of the pitch and yaw of the bird, with roll deduced using the third GPS on the helicopter.
Surface nuclear magnetic resonance (surface NMR) soundings are geophysical techniques that offer direct detection of groundwater. Ordinary surface NMR soundings are achieved with a wire loop that acts as both transmitter and receiver. We extend the capability of the technique by using a grounded electrical bipole as the measurement sensor. We provide the first successful measurements of surface NMR signals taken with a grounded electrode pair on a beach outside Perth, Western Australia. Simple changes to existing equations are sufficient to provide forward models for the changes in measurement technique, and the resulting groundwater models are consistent with coincident loop soundings. Our result opens the field for novel sounding techniques of surface NMR signals that could have broad impact on near‐surface groundwater investigations.
Airborne geophysical surveys routinely collect data along traverse lines at sample spacing distances that are two or more orders of magnitude less than between-line separations. Grids and maps interpolated from such surveys can produce aliasing; features that cross flight lines can exhibit boudinage or string-of-beads artifacts. Boudinage effects can be addressed by novel gridding methods. Following developments in geostatistics, a nonstationary nested anisotropic gridding scheme is proposed that accommodates sampling and data anisotropy in geophysical surveys. Computation is reduced by including anchor points throughout the interpolation region that contain localized anisotropy information that is propagated throughout the survey area with a smoothing kernel. Additional anisotropy can be required at certain locations in the region to be gridded. A model selection scheme is proposed that uses Laplace approximations for determining whether increased model complexity is supported by the surrounding data. The efficacy of the method is shown using a synthetic data set obtained from satellite imagery. A pseudogeophysical survey is created from the image and reconstructed with this method. Two case histories are selected for further elucidation from airborne geophysical surveys conducted in Western Australia (WA). The first example illustrates improvement in gridding the depth of paleochannels interpreted from along-line conductivity-depth models of a regional airborne electromagnetic (AEM) survey in the Mid West WA region. The second example indicates how improvements can be made in producing grids of aeromagnetic data and inverted electrical conductivity from an AEM survey conducted in the Pilbara region. In both case histories, nested anisotropic kriging reduces the expression of boudinage patterns and sharpens crossline features in the final gridded products permitting increased confidence in interpretations based on such products.