Huan Ding

Dr. Huan Ding

Louisiana State University
orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 May 2022 in Materials
Verified
Journal Article
Open access
PDF file
Congyuan ZengCongyuan Zeng
Congyuan Zeng
HGHamed Ghadimi
Hamed Ghadimi
Huan DingHuan Ding
Huan Ding
SNSaber Nemati
Saber Nemati
AGAbdelrahman Garbie
Abdelrahman Garbie
SGShengmin Guo
Shengmin Guo
In this paper, the phase structure, composition distribution, grain morphology, and hardness of Al6061 alloy samples made with additive friction stir deposition (AFS-D) were examined. A nearly symmetrical layer-by-layer structure was observed in the cross section (vertical with respect to the fabrication-tool traversing direction) of the as-deposited Al6061 alloy samples made with a back-and-forth AFS-D strategy. Equiaxed grains were observed in the region underneath the fabrication tool, while elongated grains were seen in the “flash region” along the mass flow direction. No clear grain size variance was discovered along the AFS-D build direction except for the last deposited layer. Grains were significantly refined from the feedstock (~163.5 µm) to as-deposited Al6061 alloy parts (~8.5 µm). The hardness of the as-fabricated Al6061 alloy was lower than those of the feedstock and their heat-treated counterparts, which was ascribed to the decreased precipitate content and enlarged precipitate size.

2 February 2023 in Materials
Verified
Journal Article
Open access
PDF file
HGHamed Ghadimi
Hamed Ghadimi
Huan DingHuan Ding
Huan Ding
SESelami Emanet
Selami Emanet
MTMojtaba Talachian
Mojtaba Talachian
CCChase Cox
Chase Cox
SGShengmin Guo
Shengmin Guo
The solid-state additive friction stir deposition (AFSD) process is a layer-by-layer metal 3D-printing technology. In this study, AFSD is used to fabricate Al–Cu–Li 2050 alloy parts. The hardness values for various regions of the as-deposited built parts are measured, and the results are contrasted with those of the feedstock material. The as-fabricated Al2050 parts are found to have a unique hardness distribution due to the location-specific variations in the processing temperature profile. The XRD results indicate the presence of the secondary phases in the deposited parts, and EDS mapping confirms the formation of detectable alloying particles in the as-deposited Al2050 matrix. The AFSD thermal–mechanical process causes the unique hardness distribution and the reduced microhardness level in the AFSD components, in contrast to those of the feedstock material.

14 January 2024 in Metals
Verified
Journal Article
Open access
PDF file
HGHamed Ghadimi
Hamed Ghadimi
MTMojtaba Talachian
Mojtaba Talachian
Huan DingHuan Ding
Huan Ding
SESelami Emanet
Selami Emanet
SGShengmin Guo
Shengmin Guo
Solid-state additive friction stir deposition (AFSD) is a thermomechanical-based additive manufacturing technique. For this study, AFSD was utilized to produce aluminum alloy 6061 (AA6061) blocks with varying layer thicknesses (1 mm, 2 mm, and 3 mm). The mechanical properties were assessed through uniaxial tensile tests and Vickers microhardness measurement, and statistical analysis was employed to investigate differences among data groups. The results revealed that the deposition layer thickness influences tensile properties in the building (Z) direction, while the properties in the X and Y directions showed minor differences across the three AFSD blocks. Furthermore, variations in tensile properties were observed depending on the sample orientation in the AFSD blocks and its depth-wise position in the part in the building direction. The microhardness values decreased non-linearly along the building direction, spread across the width of the part’s cross-section, and highlighted that the deposition layer thickness significantly affects this property. The 1 mm block exhibited lower average microhardness values than the 2 mm and 3 mm blocks. The temperature histories and dynamic heat treatment are influenced by the deposition layer thickness and depend on the location of the point being studied in the part, resulting in variations in the microstructure and mechanical properties along the building direction and across the part’s width.

23 May 2023 in Additive Manufacturing
Verified
Journal Article
Closed access
Bin ZhangBin Zhang
Bin Zhang
Huan DingHuan Ding
Huan Ding
AMAndrew C. Meng
Andrew C. Meng
SNSaber Nemati
Saber Nemati
SGShengmin Guo
Shengmin Guo
WMW.J. Meng
W.J. Meng

4 January 2023 in Materials
Verified
Journal Article
Open access
PDF file
HGHamed Ghadimi
Hamed Ghadimi
AJArash Pourbagheri Jirandehi
Arash Pourbagheri Jirandehi
SNSaber Nemati
Saber Nemati
Huan DingHuan Ding
Huan Ding
AGAbdelrahman Garbie
Abdelrahman Garbie
SGShengmin Guo
Shengmin Guo
In this paper, small blocks of 17-4 PH stainless steel were manufactured via extrusion-based bound powder extrusion (BPE)/atomic diffusion additive manufacturing (ADAM) technology in two different orientations. Ultrasonic bending-fatigue and uniaxial tensile tests were carried out on the test specimens prepared from the AM blocks. Specifically, a recently-introduced small-size specimen design is employed to carry out time-efficient fatigue tests. Based on the results of the testing, the stress–life (S-N) curves were created in the very high-cycle fatigue (VHCF) regime. The effects of the printing orientation on the fatigue life and tensile strength were discussed, supported by fractography taken from the specimens’ fracture surfaces. The findings of the tensile test and the fatigue test revealed that vertically-oriented test specimens had lower ductility and a shorter fatigue life than their horizontally-oriented counterparts. The resulting S-N curves were also compared against existing data in the open literature. It is concluded that the large-sized pores (which originated from the extrusion process) along the track boundaries strongly affect the fatigue life and elongation of the AM parts.

11 February 2022 in Materials
Verified
Journal Article
Open access
PDF file
Huan DingHuan Ding
Huan Ding
Congyuan ZengCongyuan Zeng
Congyuan Zeng
JRJonathan Raush
Jonathan Raush
Kasra MomeniKasra Momeni
Kasra Momeni
SGShengmin Guo
Shengmin Guo
Currently, no commercial aluminum 7000 series filaments are available for making aluminum parts using fused deposition modeling (FDM)-based additive manufacturing (AM). The key technical challenge associated with the FDM of aluminum alloy parts is consolidating the loosely packed alloy powders in the brown-body, separated by thin layers of surface oxides and polymer binders, into a dense structure. Classical pressing and sintering-based powder metallurgy (P/M) technologies are employed in this study to assist the development of FDM processing strategies for making strong Al7075 AM parts. Relevant FDM processing strategies, including green-body/brown-body formation and the sintering processes, are examined. The microstructures of the P/M-prepared, FDM-like Al7075 specimens are analyzed and compared with commercially available FDM 17-4 steel specimens. We explored the polymer removal and sintering strategies to minimize the pores of FDM-Al7075-sintered parts. Furthermore, the mechanisms that govern the sintering process are discussed.