Mojtaba Talachian

Mojtaba Talachian

Auto-generated profile, based on publicly available information

Mojtaba Talachian


Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
2 February 2023 in Materials
Verified
Journal Article
Open access
PDF file
HGHamed Ghadimi
Hamed Ghadimi
Huan DingHuan Ding
Huan Ding
SESelami Emanet
Selami Emanet
MTMojtaba Talachian
Mojtaba Talachian
CCChase Cox
Chase Cox
SGShengmin Guo
Shengmin Guo
The solid-state additive friction stir deposition (AFSD) process is a layer-by-layer metal 3D-printing technology. In this study, AFSD is used to fabricate Al–Cu–Li 2050 alloy parts. The hardness values for various regions of the as-deposited built parts are measured, and the results are contrasted with those of the feedstock material. The as-fabricated Al2050 parts are found to have a unique hardness distribution due to the location-specific variations in the processing temperature profile. The XRD results indicate the presence of the secondary phases in the deposited parts, and EDS mapping confirms the formation of detectable alloying particles in the as-deposited Al2050 matrix. The AFSD thermal–mechanical process causes the unique hardness distribution and the reduced microhardness level in the AFSD components, in contrast to those of the feedstock material.

14 January 2024 in Metals
Verified
Journal Article
Open access
PDF file
HGHamed Ghadimi
Hamed Ghadimi
MTMojtaba Talachian
Mojtaba Talachian
Huan DingHuan Ding
Huan Ding
SESelami Emanet
Selami Emanet
SGShengmin Guo
Shengmin Guo
Solid-state additive friction stir deposition (AFSD) is a thermomechanical-based additive manufacturing technique. For this study, AFSD was utilized to produce aluminum alloy 6061 (AA6061) blocks with varying layer thicknesses (1 mm, 2 mm, and 3 mm). The mechanical properties were assessed through uniaxial tensile tests and Vickers microhardness measurement, and statistical analysis was employed to investigate differences among data groups. The results revealed that the deposition layer thickness influences tensile properties in the building (Z) direction, while the properties in the X and Y directions showed minor differences across the three AFSD blocks. Furthermore, variations in tensile properties were observed depending on the sample orientation in the AFSD blocks and its depth-wise position in the part in the building direction. The microhardness values decreased non-linearly along the building direction, spread across the width of the part’s cross-section, and highlighted that the deposition layer thickness significantly affects this property. The 1 mm block exhibited lower average microhardness values than the 2 mm and 3 mm blocks. The temperature histories and dynamic heat treatment are influenced by the deposition layer thickness and depend on the location of the point being studied in the part, resulting in variations in the microstructure and mechanical properties along the building direction and across the part’s width.

10 July 2026 in Progress in Additive Manufacturing
Verified
Journal Article
Open access
PDF file
YCYehong Chen
Yehong Chen
Huan DingHuan Ding
Huan Ding
SESelami Emanet
Selami Emanet
EBEhsan Bagheri
Ehsan Bagheri
MTMichael M. Talachian
Michael M. Talachian
SGShengmin Guo
Shengmin Guo
In this paper, laser powder bed fusion (L-PBF) prepared GRX-810 samples with different yttria contents (from 0.3 to 1 wt%) were systematically examined. The mechanical properties and thermal properties were measured under as-built and Hot Isostatic Pressing (HIP) heat treated conditions. The results indicate that yttria content significantly affects the thermal properties of as-built L-PBF GRX-810. Higher yttria reduces thermal diffusivity and conductivity by up to 6% in of as-built samples. HIP restores thermal properties to low-yttria levels, indicating that L-PBF-induced microdefects and porosity, rather than composition, primarily cause the thermal degradation. Based on the mechanical testing results, yttria content up to 0.45% provides the most favorable strength–ductility balance in the present dataset. Higher yttria content (from 0.5 to 1%) leads to the reduction of the elongation from 27% to around 4% in the as-built samples. Following HIP, the yield strength decreases from ~ 785 MPa in the as-built state to ~ 685 MPa. The elongation increases from 4% in the as-built state to ~ 42%. HIP samples with yttria content less than 0.45% exhibit a high ductility at approximately 40% maximum elongation, while HIP samples with yttria content higher than 0.5% exhibit a moderate ductility of approximately 18% maximum elongation at failure. These thermal and mechanical performance studies provide valuable guidance for GRX-810 applications and provide a reference for further AM-ODS alloy optimization.