We numerically and experimentally demonstrated a metamaterial perfect absorber (MPA) in MHz region based on a planar sandwiched metal-dielectric-metal structure. First, the single-peak perfect absorption was obtained at 400 MHz. The ratios of the periodicity of unit cells and the thickness to the absorption wavelength are 1/12 and 1/94, respectively. The advantage of structural design and the mechanism for the low-frequency MPA are described in detail by the comparison between calculation, simulation, and experiment. Influence of the incident angle of electromagnetic (EM) wave for both transverse-electric (TE) and transverse-magnetic (TM) polarization on absorption was also investigated, and the absorption was maintained to be above 95% at incident angles up to $30°$ . Finally, we propose a self-asymmetric structure, which induces the dual-band perfect absorption in the same range of frequency. The EM behavior of the excitation modes and the mechanism of the dual-band MPA are clearly explained. Especially, when two resonance modes are finely controlled to be close enough, the bandwidth (full width at half maximum) of MPA is enhanced to be nearly wider twice than that in case of single-peak perfect absorption. The enhanced bandwidth is still well preserved by varying the incident angle up to $30°$ for both TE and TM polarization. The results were also confirmed by both simulation and experiment. Our work is promising for potential practical applications in the radio range, such as radio-frequency shielding devices, single/dual-frequency filters, and switching devices.

In this work, we proposed a flexible broadband metamaterial perfect absorber (FBMPA) by exploiting a pasted conductive-graphene ink on a polyimide substrate. For the flat FBMPA, an absorption over 90% was found to cover a wide frequency range (from 7.88 to 18.01 GHz). The high-absorption feature was polarization-insensitive and regarded as stable with respect to the oblique incidence up to 30 degrees of electromagnetic wave. The high absorption was maintained well even when the absorber was wrapped. That is, the FBMPA was attached to cylindrical surfaces (with the varying radius from 4 to 50 cm). For both flat and curved states, the absorption mechanism was explained by the perfect impedance matching and the dielectric loss of the proposed absorber. Our work provides the groundwork for the commercialization of future meta-devices such as sensors, optical filters/switchers, photodetectors, and energy converters.

Metamaterials, recognized as advanced artificial materials endowed with distinctive properties, have found diverse applications in everyday life, military endeavors, and scientific research. Starting from monolayer metamaterials, multilayer ones are increasingly researched, especially in the field of electromagnetic wave absorption. In this article, we propose a multilayer metamaterial-absorber (MA) structure comprising two resonant layers crafted with copper and FR-4 dielectric. The presented multilayer MA structure exhibited an absorption greater than 90% in a frequency range from 4.84 to 5.02 GHz, with two maximum absorption peaks at 4.89 and 4.97 GHz. The bandwidth of the multilayer MA surpassed that of the individual single-layer MAs, with extension fractions reaching 360% and 257%, respectively. Through the simulation and calculation, the field distribution and equivalent circuit model elucidated that both individual magnetic resonances and their interplay contribute significantly to the absorption behavior of the multilayer MA. The absorption of the proposed multilayer MA structure was also investigated for the oblique incidence in the transverse electric (TE) and transverse magnetic (TM) modes. In the TE mode, the absorption intensity of two maximum peaks was maintained at over 93% up to an incident angle of 40 degrees and dropped to below 80% at an incident angle of 60 degrees. In the TM mode, the absorption was more stable and not significantly affected by the incident angle, ranging from 0 to 60 degrees. An absorption greater than 97% was observed when the incident angle increased from 0 to 60 degrees in the TM mode. Additionally, the approach in our work was further demonstrated by adding more resonant layers, making 3- and 4-layer structures. The results indicated that the absorption bandwidths of the 3- and 4-layer structures increased by 16% and 33%, respectively, compared to the bilayer structure. Furthermore, we analyzed the thermal distribution within the MA to understand the dissipation of absorbed electromagnetic energy. This research offers valuable insight into the augmented MA through a multilayer structure, presenting the implications for microwave applications like electromagnetic shielding, as well as in the design of MAs for terahertz devices and technologies, including emission and thermal imaging. These findings contribute to the advancement of knowledge in enhancing the absorption capabilities across various frequency ranges, expanding the potential applications of metamaterials.

We demonstrate a dual-band, polarization-insensitive, ultrathin and flexible metamaterial absorber (MA), based on high-order magnetic resonance. By exploiting a flexible polyimide substrate, the thickness of MA came to be 1/148 of the working wavelength. The absorption performance of the proposed structure was investigated for both planar and bending models. In the case of the planar model, a single peak was achieved at a frequency of 4.3 GHz, with an absorption of 98%. Furthermore, additional high-order absorption peaks were obtained by the bending structure on a cylindrical surface, while the fundamental peak with a high absorption was maintained well. Our work might be useful for the realization and the development of future devices, such as emitters, detectors, sensors, and energy converters.