For generating a texture or pattern on a work surface, one of the emerging processes is laser surface texturing (LST). It is an effective method for producing texture on a work surface. Literature shows that various lasers have been applied to generate textures on the surface of work materials. Recently, LST has shown tremendous potential in the field of biomedical applications. Applying the LST process, the efficacy of the biomaterial has been drastically improved. This paper presents an in-depth review of laser surface texturing for biomedical applications. The effect of LST on important biomaterial has been thoroughly studied; it was found that LST has extreme potential for surface modification of biomaterial and can be utilized for biomedical applications.
11 April 2017 in Materials and Manufacturing Processes
Laser micro-marking is an efficient technique for permanent marking and logo printing on materials. This study details the selection of an optimal parametric combination for laser micro-marking. In this work, markings were performed on Gallium Nitride (GaN) with varying the levels of marking parameters. The parameters considered in the present work are current (A), pulse frequency (Hz), and scanning speed (mm/sec). This experiment was designed using a “central composite design,” grounded in the response surface methodology. Mark intensity, which is a prominent response in laser marking, was considered the output response. The data interpretation involved analysis of variance (ANOVA) and mathematical modelling between the input parameters. It is essential to determine the relationship and significance of input-output variation. The interaction effect of various input parameters on mark intensity was also studied. Finally, two techniques, namely genetic algorithm (GA) and particle swarm optimization (PSO), were applied, and the optimal settings of input constraints were predicted.
21 June 2017 in Arabian Journal for Science and Engineering
The paper deals with the parametric analysis and ANFIS-based modeling of process parameters during turning operation of stainless steel 202. In this experimental work, the Taguchi L16 DOE was utilized for designing the experiments considering three turning parameters namely feed rate, spindle speed as well as depth of cut. All the experiment was conducted at different parametric combinations and the performance namely material removal rate (MRR) and surface roughness (Ra) were evaluated. With the help of a suitable plot, the influences of process parameters on performance were analyzed. It was observed that depth of cutis is the majority influencing parameter for varying (parametric contribution is 53.33%) the MRR, whereas in case of surface roughness, the most contributing parameter is the spindle speed (parametric contribution is 95.71%). Further, the adaptive network-based fuzzy inference system (ANFIS) based modeling has been done to understand and establish the input-output relationship. The experimental results and ANFIS predicted results were compared and it is found that the ANFIS predicted results are accurate for predicting the responses during turning operation of stainless steel 202.
14 September 2017 in Periodica Polytechnica Mechanical Engineering
Wire electric discharge machining (WEDM) is a nontraditional machining process for machining conductive materials with complex and intricate shapes with a high surface finish and dimensional accuracy. The decision making for the selection of the best set of combinations of input process parameters is a major challenge. Therefore a proper optimization tool should be used for the optimal selection of process parameters. The resent work deals with the comparative study of Preferential Selection Index (PSI) and Technique for Order of Preference by Similarity to Ideal Solution (TOPSIS) for the selection of process parameters during machining of EN31 tool steel. Four input parameters- Pulse on Time (Ton ), Pulse off Time (Toff ), Servo Voltage (SV) and the Wire tension (WT) are considered. Surface roughness and material removal rate are the measured output responses. Taguchi L9 orthogonal array is used for developing the experimental design. Three levels of each control factor are considered. The results show that a single parameter alone does not have a significant influence on the output responses. Thequality of the output responses depends on the combination of the various set of input parameters. The best set of combination suggested from the current input parameters for machining of EN31 Tool Steel by Wire EDM Process is found to be Pulse on Time (Ton )= 15μs, Pulse Off Time (Toff )=35μs, Servo Voltage (SV)=40V and the Wire tension (WT)=5kgf from both PSI as well as TOPSIS techniques. Confirmation experiments are performed to validate the optimal results.
1 February 2021 in Materials Chemistry and Physics