Defect depth profiles of Cu (In1−x,Gax)(Se1−ySy)2(CIGSS) were measured as functions of pulse width and voltage via deep-level transient spectroscopy (DLTS). Four defects were observed, i.e., electron traps of ~0.2 eV at 140 K (E1 trap) and 0.47 eV at 300 K (E2 trap) and hole traps of ~0.1 eV at 100 K (H1 trap) and ~0.4 eV at 250 K (H2 trap). The open circuit voltage (VOC) deteriorated when the trap densities of E2 were increased. The energy band diagrams of CIGSS were also obtained using Auger electron spectroscopy (AES), X-ray photoelectron spectroscopy (XPS), and DLTS data. These results showed that the valence band was lowered at higher S content. In addition, it was found that the E2 defect influenced the VOCand could be interpreted as an extended defect. Defect depth profile images provided clear insight into the identification of defect state and density as a function of depth around the space charge region.
23 July 2015 in Progress in Photovoltaics: Research and Applications
Copper Zinc Tin Sulfide (C2ZTS4) solar cells have become a fascinating research topic due to several advantages of the C2ZTS4 absorber layer, such as having non-toxic and abundantly available components. Superstrate structured C2ZTS4 solar cells were fabricated on the top of a fluorine-doped tin oxide (FTO) substrate with a spray pyrolysis method from the window layer to the absorber layer. Titanium dioxide (TiO2) and indium sulfide (In2S3) were used as the window and buffer layer, respectively. The source materials for the C2ZTS4 and buffer layers were all aqueous-based solutions. The metallic component ratio, Cu/(Zn + Sn), and the sulfur concentration in the solutions were systematically investigated. The optimum ratio of Cu/(Zn + Sn) in the film is about 0.785, while 0.18 M thiourea in the solution is the best condition for high performance. The C2ZTS4 layers deposited at lower temperatures (<360 °C) yielded a low quality resulting in low current density (JSC). On the other hand, the C2ZTS4 layers deposited at high temperature (~400 °C) showed a low fill factor (FF) without degradation of the open-circuit voltage (VOC) and JSC due to the junction degradation and high contact resistance between the absorber layer and metal contact. The best cell efficiency, VOC, JSC, and fill factor achieved were 3.34%, 383 mV, 24.6 mA/cm2, and 37.7%, respectively.
1 January 2016 in Solar Energy Materials and Solar Cells
Cu(In,Ga)(Se,S)2 (CIGSS) absorber layers were fabricated by using a modified two-stage sputter and a sequential selenization/sulfurization method, and the sulfurization process is changed from one-step to two-step. The two-step sulfurization was controlled with two different H2S gas concentrations during the sulfurization treatment. This two-step process yielded remarkable improvements in the efficiency (+0.7%), open circuit voltage (+14 mV), short circuit current (+0.23 mA/cm2), and fill factor (+0.21%) of a CIGSS device with 30 × 30 cm2 in size, owing to the good passivation at the grain boundary surface, uniform material composition among the grain boundaries, and modified depth profile of Ga and S. The deterioration of the P/N junction quality was prevented by the optimized S content in the CIGSS absorber layer. The effects of the passivation quality at the grain boundary surface, the material uniformity, the compositional depth profiles, the microstructure, and the electrical characteristics were examined by Kelvin probe force microscopy, X-ray diffraction, secondary ion mass spectrometry, scanning electron microscopy, and current-voltage curves, respectively. The two-step sulfurization process is experimentally found to be useful for obtaining good surface conditions and, enhancing the efficiency, for the mass production of large CIGSS modules.