The patterning and transfer of a two-dimensional graphene film without damaging its original structure is an urgent and difficult task. For this purpose, we propose the use of the blister-based laser-induced forward transfer (BB-LIFT), which has proven itself in the transfer of such delicate materials. The ease of implementation of laser techniques reduces the number of intermediate manipulations with a graphene film, increasing its safety. The work demonstrates the promise of BB-LIFT of single-layer graphene from a metal surface to a SiO₂/Si substrate. The effect of the parameters of this method on the structure of transferred graphene islands is investigated. The relevance of reducing the distance between irradiating and receiving substrates for the transfer of free-lying graphene is demonstrated. The reasons for the damage to the integrity of the carbon film observed in the experiments are discussed. The preservation of the original crystal structure of transferred graphene is confirmed by Raman spectroscopy.

The novel design of a terahertz large aperture photoconductive antenna (LAPCA) is reported. It features a longitudinal orientation of the bias electric field within the photoconductive substrate, and has the advantage of a small interelectrode gap, resulting in a higher field for the same applied voltage. The proposed LAPCA configuration has been tested with a nitrogen-doped (∼10 ppm) synthetic monocrystalline diamond, which is a promising material for high-intensity and high-power terahertz sources. Two antennas with different high-voltage electrode realizations were assembled, pumped by a 400 nm femtosecond laser, and tested for THz emitter function. The experimental data are found to be in good correlation with the numerical simulation results. The performance of antennas with the conventional transverse E-field configuration and the novel longitudinal configuration is compared and discussed.

It has been shown recently that a photoconductive antenna (PCA) based on a nitrogen-doped diamond can be effectively excited by the second harmonic of a Ti:sapphire laser (λ = 400 nm). The THz emission performance of the PCA can be significantly increased if a much stronger electric field is created between the close-located electrodes. To produce a homogeneous electric field over the entire excited diamond volume, the laser fabrication of deep-buried graphite electrodes inside the diamond crystal was proposed. Several electrodes consisting of the arrays of buried pillars connected by the surface graphite stripes were produced inside an HPHT diamond crystal using femtosecond and nanosecond laser pulses. Combining different pairs of the electrodes, a series of PCAs with various electrode interspaces was formed. The THz emission of the PCAs equipped with the buried electrodes was measured at different values of excitation fluence and bias voltage (DC and pulsed) and compared with the emission of the same diamond crystal when the bias voltage was applied to the surface electrodes on the opposite faces. All examined PCAs have demonstrated the square-law dependencies of the THz fluence on the field strength, while the saturation fluence fluctuated in the range of 1200–1600 µJ/cm². The THz emission performance was found to be approximately the same for the PCAs with the surface electrodes and with the buried electrodes spaced at a distance of 1.4–3.5 mm. However, it noticeably decreased when the distance between the buried electrodes was reduced to 0.5 mm.

We are reporting on laser microstructuring of thin nanocrystalline diamond membranes, for the first time. To demonstrate the possibility of microstructuring, we fabricated a diamond membrane, of 9 $\mathsf{\mu }$m thickness, with a two-dimensional periodic array of closely located chiral elements. We describe the fabrication technique and present the results of the measurements of the infrared transmission spectra of the fabricated membrane. We theoretically studied the reflection, transmission, and absorption spectra of a model structure that approximates the fabricated chiral metamembrane. We show that the metamembrane supports quasiguided modes, which appear in the optical spectra due to grating-assisted diffraction of the guided modes to the far field. Due to the C${}_4$ symmetry, the structure demonstrates circular dichroism in transmission. The developed technique can find applications in infrared photonics since diamond is transparent at wavelengths >6 $\mathsf{\mu }$m and has record values of hardness. It paves the way for creation of new-generation infrared filters for circular polarization.

Graphitized structures are fabricated on the polycrystalline diamond surface using an excimer KrF (λ = 248 nm, τ = 20 ns) and a Ti:Al₂O₃ (λ = 400 nm, τ = 120 fs) lasers. It is shown that the conductivity of formed structures is independent of the energy density and the number of pulses per surface point in the case of the excimer laser, whereas such a dependence was observed for femtosecond pulses. The causes of the dependence of the conductivity of surface structures on laser irradiation parameters are discussed.

Graphitized structures are fabricated on a polycrystalline diamond surface using an excimer KrF laser. It is found that the layer grown on the {001} crystallite, has a lower resistance and thickness...