Johan Wendel

Mr. Johan Wendel


Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 June 2020 in Nanomaterials
Verified
Journal Article
Open access
PDF file
SMSwathi Kiranmayee Manchili
Swathi Kiranmayee Manchili
JWJohan Wendel
Johan Wendel
Eduard HryhaEduard Hryha
Eduard Hryha
Lars NyborgLars Nyborg
Lars Nyborg
Iron nanopowder could be used as a sintering aid to water-atomised steel powder to improve the sintered density of metallurgical (PM) compacts. For the sintering process to be efficient, the inevitable surface oxide on the nanopowder must be reduced at least in part to facilitate its sintering aid effect. While appreciable research has been conducted in the domain of oxide reduction of the normal ferrous powder, the same cannot be said about the nanometric counterpart. The reaction kinetics for the reduction of surface oxide of iron nanopowder in hydrogen was therefore investigated using nonisothermal thermogravimetric (TG) measurements. The activation energy values were determined from the TG data using both isoconversional Kissinger–Akahira–Sunose (KAS) method and the Kissinger approach. The values obtained were well within the range of reported data. The reaction kinetics of Fe2O3 as a reference material was also depicted and the reduction of this oxide proceeds in two sequential stages. The first stage corresponds to the reduction of Fe2O3 to Fe3O4, while the second stage corresponds to a complete reduction of oxide to metallic Fe. The activation energy variation over the reduction process was observed and a model was proposed to understand the reduction of surface iron oxide of iron nanopowder.

3 November 2020 in Powder Metallurgy
Verified
Journal Article
Open access
JWJohan Wendel
Johan Wendel
SMSwathi K. Manchili
Swathi K. Manchili
EHEduard Hryha
Eduard Hryha
LNLars Nyborg
Lars Nyborg
Conventional ferrous powder metallurgy relies on uniaxial die-pressing of powder before sintering. The operation causes particle rearrangement and deformation and the initial state of the compact ultimately determines the sintering behaviour. In this study, sintering was investigated for water-atomised iron powder compacted at three different pressure levels, with and without admixed graphite. Electron back-scatter diffraction of the powder and compacts showed a large increase in low-angle grain boundaries after compaction. The sintering of the compacts was investigated by means of dilatometry in hydrogen. The initial compaction strongly influences sintering shrinkage, particularly in the low-temperature, high-diffusivity ferrite region which can account for up to 80% of the recorded shrinkage. Only a small fraction of the total shrinkage originates from the austenite phase, even at high sintering temperatures. However, the ratio of sintering shrinkage in ferrite and austenite changes with compaction pressure, carbon content and heating rate.

10 May 2018 in Surface and Interface Analysis
Verified
Journal Article
Closed access
PDF file
JWJohan Wendel
Johan Wendel
RSR. Shvab
R. Shvab
YCY. Cao
Y. Cao
EHE. Hryha
E. Hryha
LNL. Nyborg
L. Nyborg

9 May 2020 in Journal of Thermal Analysis and Calorimetry
Verified
Journal Article
Open access
PDF file
JWJohan Wendel
Johan Wendel
SMSwathi K. Manchili
Swathi K. Manchili
EHEduard Hryha
Eduard Hryha
LNLars Nyborg
Lars Nyborg
Reduction of oxides during sintering is a prerequisite for the manufacturing of powder metallurgy steels. Inadequate control of the sintering atmosphere may impede sinter neck formation and cause entrapment and growth of oxides in sinter necks, ultimately deteriorating the mechanical properties of sintered components. In this study, the oxide reduction and oxygen removal in water-atomized iron powder was investigated by means of thermogravimetric analysis in pure hydrogen. Two principal mass loss events were recorded, corresponding to the removal of the surface oxide layer at around 400 °C and reduction of internal and stable oxides in the range 600–1350 °C. The apparent activation energies of these mass loss processes were determined by means of kinetic analyses, giving values around 100 kJ mol−1 and 200–400 kJ mol−1, respectively. The validity of the results was asserted using hematite reference samples which displayed good correlation with the reduction of the surface oxide layer, thereby showing that the powder surfaces are covered by an Fe2O3 oxide. The high-temperature mass loss, with no analogy in the reference samples, is believed to originate from a combination of oxygen removal from internal oxides and stable oxide particulates on the surface. Analysis of the oxide reduction in iron powder compacts show a slightly lower activation energy for the oxide layer reduction, indicating an influence of the compaction step on the initial state of the powder and oxide layer. At the same time, the high-temperature mass loss event was shifted to higher temperatures, which is believed to be caused by the increasingly restricted mass transport of reduction products along the pores in the sintered compact.

25 June 2020 in Surface and Interface Analysis
Verified
Journal Article
Open access
PDF file
JWJohan Wendel
Johan Wendel
SMSwathi Kiranmayee Manchili
Swathi Kiranmayee Manchili
YCYu Cao
Yu Cao
Eduard HryhaEduard Hryha
Eduard Hryha
Lars NyborgLars Nyborg
Lars Nyborg
Water‐atomized iron and steel powder is commonly used as the base material for powder metallurgy (PM) of ferrous components. The powder surface chemistry is characterized by a thin surface oxide layer and more thermodynamically stable oxide particulates whose extent, distribution, and composition change during the sintering cycle due to a complex set of oxidation–reduction reactions. In this study, the surface chemistry of iron and steel powder was investigated by combined surface and thermal analysis. The progressive reduction of oxides was studied using model sintering cycles in hydrogen atmospheres in a thermogravimetric (TG) setup, with experiments ended at intermediate steps (500–1300°C) of the heating stage. The surface chemistry of the samples was then investigated by means of X‐ray photoelectron spectroscopy (XPS) to reveal changes that occurred during heating. The results show that reduction of the surface oxide layer occurs at relatively lower temperature for the steel powder, attributed to an influence of chromium, which is supported by a strong increase in Cr content immediately after oxide layer reduction. The reduction of the stable oxide particulates was shifted to higher temperatures, reflecting their higher thermodynamic stability. A complementary vacuum annealing treatment at 800°C was performed in a furnace directly connected to the XPS instrument allowing for sample transfer in vacuum. The results showed that Fe oxides were completely reduced, with segregation and growth of Cr and Mn oxides on the particle surfaces. This underlines the sequential reduction of oxides during sintering that reflects the thermodynamic stability and availability of oxide‐forming elements.

1 June 2021 in Results in Materials
Verified
Journal Article
Open access
SMSwathi K. Manchili
Swathi K. Manchili
JWJohan Wendel
Johan Wendel
MSMaheswaran Vattur Sundaram
Maheswaran Vattur Sundaram
EHEduard Hryha
Eduard Hryha
LNLars Nyborg
Lars Nyborg