Slug flow is one of the most common flow patterns in horizontal gas-liquid two-phase flow. Structure detection of slug flow is of great significance for understanding the heat and mass transfer between phases and uncovering the mechanism of flow pattern transition. However, it is remarkably difficult to accurately measure the interface structures of slug flow with a single sensing mode due to its multi-scale characteristics. In this paper, we design a combined ultrasonic and conductance sensing system that consists of a transmission ultrasonic transducer (TUT), a reflection ultrasonic transducer (RUT) and two parallel-wire conductance sensors (PWCSs). The response signals of the ultrasonic transducers and the conductance sensor for slug flows were collected in an experiment of horizontal gas-liquid flow. Based on the different measurement mechanisms of the ultrasonic transducers and the conductance sensor, the two-dimensional gas-liquid interfaces in slug flows were reconstructed. The experimental results demonstrate that, compared to the TUT and the PWCS, the RUT has obvious advantages in the detection of the local gas-liquid interface structure. In addition, based on the cross-correlation velocity measured by the PWCSs, the slug lengths in the gas-liquid flow were accessed. It was found that the slug lengths derived from the ultrasonic transducers and the conductance sensor indicate a good agreement and present complicated evolution characteristics due to the coalescence and crushing of the slugs.
Gas-liquid two-phase flows are widely encountered in industrial processes. To realize the dynamic detection of gas-liquid slug flows, a direct-image multi-electrode conductance sensor (DMCS) is optimized using the finite element method to access high measurement sensitivity. Through carrying out an experiment of vertical gas-liquid two-phase flows, the gas-liquid interfaces in slug flows are detected by the DMCS and compared to the results from a planar laser-induced fluorescence (PLIF) system. The interfaces detected by the DMCS and the PLIF system indicate a good agreement. By selecting an optimal threshold, the liquid film thicknesses around Taylor bubbles (TBs) are derived, and the asymmetry of circumferential film thickness distribution is investigated. Besides, the local cross-correlation velocities at circumferential pipe wall are measured by the DMCS. Finally, the TBs in slug flows are reconstructed based on the thickness and the velocity of the TBs. The reconstructed TBs allow for a clear indication of gas-liquid slug flow structures.
1 February 2020 in Physica A: Statistical Mechanics and its Applications
Flows of two immiscible liquids through inclined pipes are often encountered in industrial processes. The interfacial characteristics in inclined pipes are of significance for understanding the mechanism of flow pattern transition and modeling the flow parameters. This paper developed a novel experimental technique to access the interface characteristics of liquid-liquid flows, during which optical and electrical methods were successfully combined by matching the refractive index and conductivity of the flows. A planar laser-induced fluorescence (PLIF) system was set up with a continuous laser and high-speed camera. Organic and aqueous phases were chosen to match refractive indices. The liquid-liquid interface in the middle of the pipe could be clearly visualized by the PLIF system. Meanwhile, two conductance parallel-wire array probes (CPAPs) were designed to reconstruct the liquid-liquid interfaces at upward and downward pipe cross-sections. The performances of the CPAP were validated using the PLIF results and employed to investigate the liquid-liquid interfacial structures. The interfacial shape and its instability were uncovered using the reconstructed interfaces by the CPAPs.
9 December 2021 in IEEE Transactions on Instrumentation and Measurement
Oil–water–gas three-phase flows are frequently encountered in the chemical, nuclear, and petroleum industries. Due to the significant differences in physical properties of the three phases, the oil–water–gas flow structures are more complex compared with two-phase flows, which brings a great challenge to the flow parameter measurement of three-phase flows. In this study, a measurement system consisting of a conductance wire-mesh sensor (WMS) and distributed coaxial conductance sensors (CCSs) is designed to visualize the oil–water-gas flow structures. The distributed CCSs are used to monitor the conductance changes of the liquid phase and to realize the real-time correction of the gas-phase distribution obtained from the WMS. The measurement system can effectively avoid the influence of the nonconductive oil phase on the gas-phase visualization, and thus improve the accuracy of gas volume fraction measurement in oil-water-gas flows. The oil-water-gas flow structure and its evolution characteristics are studied according to the flow visualization and the probability density function (PDF) of the gas volume fraction. Notably, the effect of the dispersed oil phase on the Taylor bubble and the liquid slug is uncovered by investigating the local aerated characteristics of slug flows.