Roman Kinasz

Prof. Roman Kinasz

orcid

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 December 2021 in Applied Sciences
Verified
Journal Article
Open access
PDF file
YSYang Song
Yang Song
 Z Jun  Zhao
 Jun  Zhao
Krzysztof Adam OstrowskiKrzysztof Adam Ostrowski
Krzysztof Adam Ostrowski
Muhammad Faisal JavedMuhammad Faisal Javed
Muhammad Faisal Javed
AAAyaz Ahmad
Ayaz Ahmad
RKRoman Kinasz
Roman Kinasz
The utilization of waste material, such as fly ash, in the concrete industry will provide a valuable alternative solution for creating an eco-friendly environment. However, experimental work is time-consuming; employing soft machine learning techniques can accelerate the process of forecasting the strength properties of concrete. Ensemble machine learning modeling using Python Jupyter Notebook was employed in the forecasting of compressive strength (CS) of high-performance concrete. Multilayer perceptron neuron network (MLPNN) and decision tree (DT) were used as individual learning which then ensembled with bagging and boosting to provide strong correlations. Random forest (RF) and gradient boosting regression (GBR) were also used for prediction. A total of 471 data points with input parameters (e.g., cement, fine aggregate, coarse aggregate, superplasticizer, water, days, and fly ash), and an output parameter of compressive strength (CS), were retrieved to train and test the individual learners. Cross-validation with K-fold and statistical error (i.e., MAE, MSE, RMSE, and RMSLE) analysis was applied to check the accuracy of all models. All models showed the best correlation with an ensemble model rather than an individual one. DT with AdaBoost and random forest gave a strong correlation of R2 = 0.89 with fewer errors. Cross-validation results revealed a good response with an error of less than 10 MPa. Thus, ensemble modeling not only trains the data by employing several weak learners but also produces a robust correlation that can then be used to model and predict the mechanical performance of concrete.

16 March 2022 in Materials
Verified
Journal Article
Open access
PDF file
GKGrzegorz Piotr Kaczmarczyk
Grzegorz Piotr Kaczmarczyk
RKRoman Kinasz
Roman Kinasz
VBVitaliy Bilozir
Vitaliy Bilozir
IBIvanna Bidenko
Ivanna Bidenko
This paper proposes the use of X-ray computed tomography (µCT, xCT) measurements together with finite element method (FEM) numerical modelling to assess bond failures mechanism of fiber-reinforced fine-grain concrete. Fiber-reinforced concrete is becoming popular for application in civil engineering structures. A dynamically developing topic related to concretes is the determination of bond characteristics. Nowadays, modern technologies allow inspecting the inside of the element without the need to damage its structure. This paper discusses the application of computed tomography in order to identify damage occurring in the structure of fiber-reinforced fine-grain concrete during bond failure tests. The publication is part of a larger study to determine the bonding properties of Ukrainian steel fibers in fine-grain concrete. The authors focused on the visual evaluation of sections obtained from tomographic data. Separately, the results of volumetric analysis were presented to quantitatively assess the changes occurring in the matrix structure. Finite element analysis is an addition to the substantive part and allows us to compare real damage areas with theoretical stress concentration areas. The result of the work is the identification of a path that allows verification of the locations where matrix destruction occurs.

30 June 2024 in Mining of Mineral Deposits
Verified
Journal Article
Closed access
OIOleksii Ishchenko
Oleksii Ishchenko
LNLeonid Novikov
Leonid Novikov
IPIvan Ponomarenko
Ivan Ponomarenko
VKVolodymyr Konoval
Volodymyr Konoval
RKRoman Kinasz
Roman Kinasz
KIKostiantyn Ishchenko
Kostiantyn Ishchenko
Purpose. The research aims to assess the efficiency and performance of solid media destruction in directed blasting of a charge with variable cross-sectional shape. Methods. Numerical modelling of the blast wave interaction process is performed using the finite element method based on the Euler-Lagrange algorithm. The Johns-Wilkins-Lee equation of state is used to determine the pressure-volume dependences of medium destruction. Assessment of solid medium destruction mechanism during a directed blasting of a charge with variable cross-sectional shape is carried out based on polarization-optical method on models made of optically active material. Findings. Experimental studies of solid medium destruction by the action of directed blasting with a variable cross-section charge made it possible to determine the direction of blast wave propagation and its amplitude in stress wave, influencing the intensity of radial crack network formation in superposition areas, and directed perpendicularly to explosive cavity. At the same time, the average peak pressure in collision zone of two shock waves in centre of spherical cavity is approximately 1.48 and 1.84 times higher than that in weakly blast-loaded areas. It has been found that when two shock waves collide and superimpose on each other, the intensity of their impact increases. Moreover, the shock wave velocity in collision zone is higher than that of the radial shock wave. Originality. It has been determined that the maximum pressure values on the explosive cavity wall at the initiation points sharply increase and then gradually stabilize as the blast stress waves propagate and have an arbitrary distribution pattern. Three areas should be considered: not superimposed, weakly superimposed, and strongly superimposed. At each point of detonation, the pressure on explosive cavity wall will be minimal, while in the charge centre in the spherical insert zone, on the contrary, it will be maximal. In this case, the pressure in the central superposition area is about 2.84 times greater than at the initiation ends, and the nature of distribution changes according to a linear dependence. Practical implications. The performed research findings can serve as a basis for development of effective parameters of resource-saving methods for stripping hard rocks of complex structure in the conditions of ore mines.

1 September 2019 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
RKRoman Kinasz
Roman Kinasz
VBVitaliy Bilozir
Vitaliy Bilozir
RSRoman Shmyh
Roman Shmyh
VBVolodymyr Bilozir
Volodymyr Bilozir
IBIvanna Bidenko
Ivanna Bidenko
Ukrainian enterprises of PET (Polyethylene Terephthalate) waste recycling are still capable of processing only 1 thousand tons, and more than 10 thousand tons of PET granulate are imported to Ukraine every month. Therefore, the issue of reuse and disposal of used polyethylene terephthalate, especially in construction, is one of paramount importance. The aim of the research is experimental-theoretical study of the strength of bending of prisms, reinforced with fibers and strip reinforcement of used PET bottles. Objectives of the research: the study of the percentage of reinforcing fibers in volume (1% and 1.5%) influence on the flexural strength of concrete reinforced prisms, and the possibility of using ribbon reinforcement from used PET bottles for bending concrete elements, elaboration of proposals for the deformation method of calculation of PET fibrobone bent elements. In this research the experimental methods for determining the bending strength of prisms, reinforced by fibrous, trips and PET waste tapes; methods of materials resistance theory have been used. During the research, two concrete prisms of 400x100x10 mm were constructed and tested for compression together with two concrete prisms of three-point bend for a run of 350 mm, two PET-fibrous concrete prisms for bending with percentages of reinforcement in volume of 1% and 1, 5% and two prisms for bending, reinforced with glued PET strips, with 1% reinforcement per section area. As a disperse reinforcement, pre-fabricated PET bottles of 50x3x0.2 mm were used, designed in way that the required length of sealing in the concrete is no longer than half the length of the fibers. Strip fittings are made of 4 fragments of PET bottles of 200x80x0.25 mm in size, glued with cyanacrylate adhesive with each other, and 2 fragments of 120x80x0.2 mm in size, which glued on both ends to 4 glued sheets with a length of 30 mm. Thus, the total length of the reinforcing strip is equal to 380 mm. At the final sections of the tapes, 6 openings with a diameter of 5 mm were punched to improve the anchoring. The reinforcing strips were placed in the forms located 10 mm from the lower edge. According to the results of the tests, the average cubic strength of concrete is 31.21 MPa, of prisms - 23.23 MPa, the initial module of deformation - 28.02·103 MPa. The flexural strength of prisms without a fibre is 58.54 kN·cm, with 1% fibers in volume - 64.31 kN·cm, with 1.5% fibers in volume - 71.84 kN·cm, and of prisms, reinforced with glued PET ribbons – 79.80 kN·cm. As a result of the tests, it was demonstrated that the strength of the tapes was not used properly, and the fracture was fragile due to the loss of adhesion to concrete. Analysis of the results of experimental studies allowed us to develop a deformation methodology of calculating PET-fiber-concrete bending elements.

23 February 2019 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
RKRoman Kinasz
Roman Kinasz
VBVitaliy Bilozir
Vitaliy Bilozir
RSRoman Shmyh
Roman Shmyh
AVAndriy Vysochenko
Andriy Vysochenko
In 2013, Lviv National Agrarian University patented reinforced concrete beams containing fibre external reinforcement and steel reinforcement tape with end anchors. Such technical solutions aimed at significantly reducing the cost of construction by reducing the complexity of manufacturing due to the complete replacement frames and ribbon fibre. The task of this work was to determine experimentally the bearing capacity of normal sections of steel-fibre reinforced beams with ribbon valves and compare them with the designed according to normative documents and to develop proposals for a refined calculation methodology. For studies of the bearing capacity of normal sections, 3 beams were manufactured in the size of 1500x150x60 mm. The first beam B-1, reinforced with steel strip valves in the sizes of 1500x60x3 mm with end stops, executed without fibres; The second and third beams (BF-2, BF-3) contained, in addition to the specified reinforcement, fibres in the amount of 1.59 kg and 2.12 kg, which corresponded to the coefficient of fibre reinforcement in volume, ρfv=1.5% i 2% respectively. For disperse reinforcement, an anchor fibre type with curved ends HE 1050 type in diameter of 1 mm and length of 50 mm was taken, because it is a mass produced fibre in Ukraine and abroad. The percentage of fibrous reinforcement in the volume of samples taken = 1.5% and 2%, to obtain a power effect, ensuring a sufficient bearing capacity for both normal and inclined cross-sections. As a binder for the production of concrete C20/25, cement of the mark 400 (activity 42.3 MPa). Experimental samples were made of fine-grained concrete, for the manufacture of which Yasinetskyi sand was used with a grain size unit of no more than 2.5. The composition of the mixture was chosen in such a way that the fibres could not settle down to the bottom of the forms; the cone's settling did not exceed 4-6 cm. Characteristic issue was that with an increase in the number of fibre reinforcement in the beams there was a large number of cracks. Closer to the supports, they were tilted to the longitudinal axis, indicating a joint effect on the cracking process, both bending moments and transverse forces. It has been experimentally established that the bearing capacity of steel-fibre reinforced composite reinforced beams was 16% and 21% higher than the percent reinforcement of fibres 1.5 and 2, respectively, in comparison with steel concrete. For identical values of bending moments of strain relief, the deformation of the extreme compressed fibres of concrete and the deflection of beams containing fibres are smaller than fibres without beams. The calculation of the deformation method gave a good convergence of theoretical and experimental results. Ukrainian norms for the design of steel-fibre-reinforced concrete structures require the replacement of a power calculation method using rectangular stresses of strain with a deformation method.

24 June 2020 in Materials
Verified
Journal Article
Open access
PDF file
Krzysztof Adam OstrowskiKrzysztof Adam Ostrowski
Krzysztof Adam Ostrowski
RKRoman Kinasz
Roman Kinasz
Piotr DybełPiotr Dybeł
Piotr Dybeł
With the development of concrete technology, the tendency to combine different materials with each other to achieve a greater efficiency and durability of structures can be observed. In the modern construction industry, various materials and techniques are increasingly being combined in order to achieve e.g., an increased resistance to dynamic impacts of a structure, or an increased scope of work of a selected constructional element, which translates into a significant increase in the energy of destruction. Thus, hybrid elements, known as composite ones, are created, which consist of concrete and reinforcements. This study examined the influence of the preparation of the concrete surface on the behavior of high-performance, self-compacting, fiber-reinforced concrete (HPSCFRC), reinforced with carbon fibers (CF) using a cement matrix. In the general lamination processes, this is preformed using epoxy resin. However, epoxy resin is sensitive to relatively low temperatures, and therefore the authors attempted to use a cement matrix in the lamination process. When connecting hardened concrete with a fresh concrete matrix or mixture, the type of the concrete surface is significant. In this research, three types of concrete surfaces e.g., unprepared, sanded and grinded were considered. All of the surfaces were examined using a 3D laser scanner, to determine the Abbott-Firestone profile material share curve. In this research, cylindrical concrete specimens were reinforced with one, two and three layers of laminates. They were then subjected to a uniaxial compressive test. The results of tests showed that the use of cement matrix in the lamination process, due to its low efficiency, should not be applied when reinforcing concrete elements with a high compressive strength. Moreover, the grinded surface of concrete showed the best cooperation with CF reinforcement.