This paper presents a study of the Ti-6Al-4V alloy milling under different lubrication conditions, using the minimum quantity lubrication approach. The chosen material is widely used in the industry due to its properties, although they present difficulties in terms of their machinability. A minimum quantity lubrication (MQL) prototype valve was built for this purpose, and machining followed a previously defined experimental design with three lubrication strategies. Speed, feed rate, and the depth of cut were considered as independent variables. As design-dependent variables, cutting forces, torque, and roughness were considered. The desirability optimization function was used in order to obtain the best input data indications, in order to minimize cutting and roughness efforts. Supervised artificial neural networks of the multilayer perceptron type were created and tested, and their responses were compared statistically to the results of the factorial design. It was noted that the variables that most influenced the machining-dependent variables were the feed rate and the depth of cut. A lower roughness value was achieved with MQL only with the use of cutting fluid with graphite. Statistical analysis demonstrated that artificial neural network and the experimental design predict similar results.
2 October 2023 in The International Journal of Advanced Manufacturing Technology
O sistema Toyota de Produção é muito utilizado nas indústrias visando minimização de desperdícios e perdas. Nesse contexto, o kanban surge como ferramenta de gerenciamento de estoques para apoiar o sistema Just in time buscando uma maior eficiência dos processos produtivos. No curso de Engenharia de Produção é de fundamental importância o entendimento e aplicação desses conceitos. Esta proposta de trabalho permeia o aprendizado dos alunos utilizando metodologias ativas em que o lúdico possui um caráter desafiador. Os alunos são instigados a criar sua própria fábrica, (contextualizada em uma linha de produção), criar os postos de trabalho, dimensionar os estoques por meio de cartões kanban e, colocar a linha de produção para funcionar. Como as linhas de produção criadas pelos alunos são diferenciadas, os dimensionamentos dos cartões kanban propõe questionamentos sobre tempo de espera, quantidade de peças nos contentores, movimentações de cartões pelos operadores e abastecedores, além dos tempos de produção. Questionamentos são realizados e adequações aos processos produtivos são implementados. Neste aspecto os alunos vivenciam situações reais de produção e movimentações de estoques buscando uma produtividade maior e adequada para os processos produtivos idealizados por eles. A comparação com linhas de produção reais é realizada. Percebe-se um envolvimento maior dos estudantes para com o tema, um aprendizado dos conceitos facilitado por esta abordagem, além de uma maior troca de experiências entre professor e aluno.
This study presents a preliminary integrated numerical-experimental methodology to analyze engineered surfaces produced by dry milling of AISI 303 and AISI 304 austenitic stainless steels. These steels were selected for their distinct microstructural characteristics and industrial relevance. Experimental characterization included optical and scanning electron microscopy, chemical composition analysis, tensile testing, Vickers microhardness testing, and surface topography measurements to comprehensively assess material behavior and surface quality after milling. Finite element modeling, using Deform 3D software, simulated the milling process, incorporating temperature- and strain-ratedependent material properties. The simulations predicted cutting forces and cutting energy, enabling comparison with experimental results. Key findings revealed that microstructural heterogeneities, such as MnS inclusions in AISI 303, influence deformation mechanisms, surface roughness, and plasticity index, which correlates with surface integrity. The higher sulfur content in AISI 303 can induce localized precipitation hardening, resulting in increased hardness but reduced ductility compared to AISI 304. Numerical results indicated that AISI 304 required higher cutting energy due to its homogeneous microstructure and ductility. At the same time, AISI 303 exhibited better machinability with lower energy consumption but more pronounced surface adhesion and tearing. This hybrid approach enabled mapping machining parameters to surface quality indicators, thereby supporting the optimization of cutting conditions. The elastic modulus-to-hardness ratio in plasticity index appears as a relevant factor affecting surface formation and cutting forces. Overall, this methodology provides valuable insights into the interaction between material properties, machining parameters, and surface engineering outcomes, thereby contributing to the development of enhanced manufacturing strategies for stainless steel components.