Ed Claudio Bordinassi

Dr. Ed Claudio Bordinassi


Research Focus & Metrics

Academic Career Length

19Years (2008-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 August 2020 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
AFAdalto Farias
Adalto Farias
SASérgio Luiz Rabelo de Almeida
Sérgio Luiz Rabelo de Almeida
SDSergio Delijaicov
Sergio Delijaicov
VSVanessa Seriacopi
Vanessa Seriacopi
EBEd Claudio Bordinassi
Ed Claudio Bordinassi

24 February 2018 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
MSMarcelo Otávio dos Santos
Marcelo Otávio dos Santos
GBGilmar F. Batalha
Gilmar F. Batalha
EBEd Claudio Bordinassi
Ed Claudio Bordinassi
GMGelson F. Miori
Gelson F. Miori

25 June 2020 in Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
Verified
Journal Article
Closed access
PDF file
NPNelson Wilson Paschoalinoto
Nelson Wilson Paschoalinoto
EBEd Claudio Bordinassi
Ed Claudio Bordinassi
RBRoberto Bortolussi
Roberto Bortolussi
FLFabrizio Leonardi
Fabrizio Leonardi
SDSergio Delijaicov
Sergio Delijaicov
This study focused on determining the residual stress of SAE 52100 hard-turned steel. The objective was to evaluate and compare the effects of the cutting-edge geometry and cutting parameters (cutting speed, feed rate, and cutting depth) on the residual stresses of three different conventional inserts: S-WNGA08 0408S01020A 7025, T-WNGA08 0408T01020A 7025, and S-WNGA432S0330A 7025. Tests were performed on 60 samples of SAE 52100 hardened steel with an average hardness of 58.5 HRC. The circumferential residual stresses of the samples were measured by X-ray diffraction. A full factorial design of experiments with three factors and two levels each with two central points and a replicate was used for a statistical analysis. The most significant results were as follows: For all inserts, the measured residual stresses were compressive, which extended the tool lifespan. The residual stresses of the Type-S inserts were significantly influenced by the cutting speed and depth, and those of the Type-T insert were significantly influenced by the feed rate and cutting depth. In addition, the residual stresses of the insert 3 were more compressive than those of the other two types of inserts. In other words, residual stresses are more compressive for inserts with larger chamfer angles even as the principal residual stress profiles were all compressive. This work has also shown that it is possible to determine a significant statistical relationship between cutting forces and residual stresses, allowing force measurements to predict the residual stress without any information on process parameters.

30 September 2022 in Journal of the Brazilian Society of Mechanical Sciences and Engineering
Verified
Journal Article
Closed access
PDF file
AFAdalto Farias
Adalto Farias
MSMarcelo Otávio dos Santos
Marcelo Otávio dos Santos
EBEd Claudio Bordinassi
Ed Claudio Bordinassi

30 August 2020 in Materials
Verified
Journal Article
Open access
PDF file
NPNelson Wilson Paschoalinoto
Nelson Wilson Paschoalinoto
GBGilmar Ferreira Batalha
Gilmar Ferreira Batalha
EBEd Claudio Bordinassi
Ed Claudio Bordinassi
JFJorge Antonio Giles Ferrer
Jorge Antonio Giles Ferrer
AFAderval Ferreira de Lima Filho
Aderval Ferreira de Lima Filho
CCCristiano Cardoso
Cristiano Cardoso
This paper presents a study of the Ti-6Al-4V alloy milling under different lubrication conditions, using the minimum quantity lubrication approach. The chosen material is widely used in the industry due to its properties, although they present difficulties in terms of their machinability. A minimum quantity lubrication (MQL) prototype valve was built for this purpose, and machining followed a previously defined experimental design with three lubrication strategies. Speed, feed rate, and the depth of cut were considered as independent variables. As design-dependent variables, cutting forces, torque, and roughness were considered. The desirability optimization function was used in order to obtain the best input data indications, in order to minimize cutting and roughness efforts. Supervised artificial neural networks of the multilayer perceptron type were created and tested, and their responses were compared statistically to the results of the factorial design. It was noted that the variables that most influenced the machining-dependent variables were the feed rate and the depth of cut. A lower roughness value was achieved with MQL only with the use of cutting fluid with graphite. Statistical analysis demonstrated that artificial neural network and the experimental design predict similar results.

2 October 2023 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
EBEd Claudio Bordinassi
Ed Claudio Bordinassi
VSVanessa Seriacopi
Vanessa Seriacopi
MSMarcelo Otávio dos Santos
Marcelo Otávio dos Santos
NPNelson Wilson Paschoalinoto
Nelson Wilson Paschoalinoto
AFAdalto Farias
Adalto Farias