The pollution due to non-degradable material such as plastics, has led to studies about the development of environmental-friendly materials. Because of natural sources-based materials and their biodegradability, polylactid acid (PLA) and ijuk fiber are interesting to be modified into a composite. Furthermore this study is also expected to reduce the impact of environmental problems. Surface modification of ijuk fiber through alkalinization, was aimed to enhance compatibility between the ijuk fiber and the PLA, in order to improve properties of the composite such as crytallinity and thermal behavior. To investigate in detail about this modification, this research also studied effect of the alkalinized ijuk fiber and the PLA composition to the crystallinity and the thermal behavior of the composites. The experimental results were investigated by FTIR to qualitatively analyze compounds content in the ijuk fiber before and after alkalinization, DSC and TGA to study crystallinity and thermal stability behavior of the composite, respectively and FE-SEM to observe morphological behavior like compatibility between the ijuk fiber and the PLA. The FE-SEM observation showed that alkalinization of the ijuk fiber led to wettability enhancement between the ijuk fiber and the PLA. This may be caused by annihilating lignin and hemicellulose. Furthermore this treatment leads to expose micro-fibril cellulose (MFC) in the ijuk fiber and then to enhancement of bonding affinity with the PLA. This phenomenon gives a possibility for the PLA in the composite to increase its crystallinity due to nucleating effect of crystalline parts in the MFC. DSC measurements show that addition of the alkalinized ijuk fiber tends to increase the crystallinity of PLA in the composites.Keywords: alkalization, Arenga Pinnata, compatibility, crystallinity, PLA, thermal stability
A natural fiber is an environmentally benign material since it naturally decomposed in a short time, has decent mechanical strength properties, and is in abundance. Oil palm empty fruit bunch (OPEFB) is a natural fiber that has potency as a composite reinforcement. The amorphous components of OPEFB such as lignin and hemicellulose can be removed by chemical treatment to produce microfibrillated cellulose with high crystallinity and good compatibility towards the matrix. The combination treatment was carried out using the main reagents NaOH, H2O2, and CH3COOH. The samples were characterized using FE-SEM, FTIR, STA by TGA calculation, XRD, and contact angle test. The best fiber was obtained through the alkalinization process followed by immersion using H2O2 0.20 M and C2H4O3 (paracetic acid) as a combination of H2O2 0.50 M and CH3COOH 0.15 M. The defibrillation process produced fibers with a diameter of 9 µm, a crystallinity index of 88.7%, and an increased hydrophobicity with a contact angle of 37.472o.
Recently, the use of natural fibers as reinforcing agents or fillers in thermoplastic polymer matrices has been of much concern to researchers because they are renewable, environmentally friendly and abundant in nature. In addition to the benefits provided by natural fibers, the strong polar nature of the surface causes its use as a reinforcement in the thermoplastic non-polar matrix to be limited. This problem can be overcome by surface treatment methods that aim to change the polar properties of natural fibers to be non-polar, so that the compatibility of natural-thermoplastic polymer fibers becomes better. In this study, the method of natural fiber treatment, namely bleaching-hydrolysis and TEMPO treatment was applied to Dendrocalumus Asper fibers (betung bamboo). The effect of chemical treatment on crystallinity index was evaluated by XRD instruments. FE-SEM and FTIR were used to describe the morphology and chemical composition of treated and untreated fibers. Based on the results of the data obtained from the experiment, it was shown that the fibers undergoing bleaching-hydrolysis treatment produced better crystallinity index properties than TEMPO treatment and untreated fibers.
Impact Polypropylene Copolymer (IPC) is one of the PP type which is widely used. IPC was made with addition of ethylene in PP which decreases PP crystallinity. Many efforts have been made to improve the properties of PP crystallinity by addition of nucleating agents. In this study, we use Arenga Pinnata “Ijuk” fiber as PP nucleating agent. In order to determine the effect of “Ijuk” fiber as nucleating agents in kinetics aspect, we used DSC measurement based on Avrami equation. The results showed that the addition of ijuk decreases crystallizationhalf timeand dimension of crystal growth which indicate the effects of “Ijuk” fiber as a nucleating agent.