A comparative study on different enteric-coated hard capsules was performed. The influence of different formulation factors like choice of enteric polymer, triethyl citrate (TEC) concentration (plasticizer), talc concentrations (anti-tacking agent), and different coating process parameters on the sealing performance of the capsule and the disintegration time were investigated. Furthermore, the influence of different disintegration test methods (with disc vs. without disc and 50 mM U.S. Pharmacopoeia (USP) buffer pH 6.8 vs. biopredictive 15 mM phosphate buffer pH 6.5) was evaluated. All formulations showed sufficient but not equivalent acid resistance when tested. Polymer type was the main factor influencing the capsule sealing and disintegration time. In addition, TEC and talc could affect the performance of the formulation. Regarding the choice of the disintegration test method, the presence of a disc had for the most part only limited influence on the results. The choice of disintegration buffer was found to be important in identifying differences between the formulations.

The downstream processing of hot-melt extruded amorphous solid dispersions (ASDs) into tablets is challenging due to the low tabletability of milled ASDs. Typically, the extrudate strand is sized before milling, as the strand cannot be fed directly into the milling system. At the lab scale, the strand can be sized by hand-cutting before milling. For scaling up, pelletizers or chill roll and flaker systems can be used to break strands. Due to the different techniques used, differences in milling and tablet compaction are to be expected. We present a systematic study of the milling and tableting of an extruded ASD of itraconazole with hypromellose acetate succinate (HPMCAS) as a carrier polymer. The strand was sized using different techniques at the end of the extruder barrel (hand-cutting, pelletizer, or chill roll and flaker) before being milled at varying milling speeds with varying screen sizes. The effects of these variables (sizing technology, milling speed, and screen size) on the critical quality attributes (CQAs) of the milled ASD, such as yield, mean particle size (D50), tablet compaction characteristics, and tablet dissolution, were established using response surface methodology. It was found that the CQAs varied according to sizing technology, with chill roll flakes showing the highest percentage yield, the lowest D50, and the highest tabletability and dissolution rate for itraconazole. Pearson correlation coefficient tests indicated D50 as the most important CQA related to tabletability and dissolution. For certain milling conditions, the milling of hand-cut filaments results in similar particle size distributions (PSDs) to the milling of pellets or chill roll flakes.

As final attributes of dosage form largely depend on the properties of excipients used, understanding the effect of physicochemical properties of excipients is important. In the present study, six grades of L-HPC with varying degrees of particle size and hydroxypropyl content and the influence of the grade on compaction as well as disintegration behavior were studied. All grades of L-HPC were compressed at different compression loads to achieve different tablet porosity. Compressibility and compactibility of L-HPC grades were evaluated using a modified Heckel equation and percolation model. Further effects of particle size and hydroxypropyl content of L-HPC on tablet porosity and disintegration time were evaluated using a 3² full-factorial design. From compaction studies, it was found that compressibility of L-HPC largely depends upon the particle size with lower particle size grade showing lower compressibility. Whereas consolidation/bonding behavior of L-HPC is independent of particle size and % hydroxypropyl content. By factorial design, it was found that particle size and % hydroxypropyl content have a significant effect on the disintegration behavior of L-HPC. It was found that smaller particle sizes and higher hydroxypropyl content of L-HPC show longer disintegration time. Thus, careful consideration of excipients selection should be made to achieve desired quality attribute of the product.

Despite wide commercial application of hypromellose acetate succinate (HPMCAS) in spray-dried amorphous solid dispersion (ASD) drug products, little information is available in the references on downstream processing of spray-dried dispersions with HPMCAS. Poor flow and high dilution factor are a challenge in formulating spray-dried ASDs into tablets, leaving little space for other excipients facilitating binding and disintegration. Direct compression is not possible due to the poor powder flow of spray-dried ASDs. Moisture has to be avoided due to the plasticizing properties of water on the ASD, resulting in reduced stability of the amorphous state. Thus, dry granulation by roller compaction and subsequent tablet compression is the preferred downstream process. We report the investigation of downstream processing by roller compaction and tablet compression of a high load formulation with 75% of spray-dried amorphous solid dispersion (Nifedipine:HPMCAS 1:2). A head to head comparison of microcrystalline cellulose/croscarmellose (MCC/cl-NaCMC) as binder/disintegrant vs. MCC and low-substituted hydroxypropyl cellulose (L-HPC) as excipient for binding and disintegration showed improved re-workability of the formulation with MCC/L-HPC after roller compaction. Upon transfer to the rotary press, a 45% higher tensile strength of tablets is observed after dry granulation with MCC/L-HPC.