Gábor Gyarmati

Dr. Gábor Gyarmati

Institute of Foundry Engineering, University of Miskolc, Miskolc, Borsod-Abaúj-Zemplén, Hungary
orcid
Assistant professor, researcher

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 November 2019 in Materials Characterization
Verified
Journal Article
Closed access
Gábor GyarmatiGábor Gyarmati
Gábor Gyarmati
GFGyörgy Fegyverneki
György Fegyverneki
TMTamás Mende
Tamás Mende
MTMonika Tokár
Monika Tokár

20 February 2020 in International Journal of Metalcasting
Verified
Journal Article
Open access
PDF file
Gábor GyarmatiGábor Gyarmati
Gábor Gyarmati
GFGyörgy Fegyverneki
György Fegyverneki
MTMonika Tokár
Monika Tokár
TMTamás Mende
Tamás Mende
In order to produce cast components, which meet the quality requirements of the automotive and aerospace industries, the control of liquid metal quality prior to the casting process is essential. Rotary degassing is the most commonly used melt treatment method in the foundry industry, which can effectively reduce the inclusion and solute hydrogen content of the metal. This procedure is often combined with fluxing, which allows more efficient inclusion removal during melt processing. In this study, the effects of rotary degassing treatments executed with and without flux addition on the melt cleanliness were compared. The quality of the molten metal was characterized by the microscopic inspection of K-mold specimens, X-ray computed tomography of reduced pressure test samples, and by Density-Index evaluation. The inclusions found on the fracture surfaces of K-mold samples were analyzed with energy-dispersive X-ray spectroscopy. Based on the results, rotary degassing coupled with flux addition can be an effective inclusion and solute hydrogen removal technique that can significantly improve melt quality. On the other hand, rotary degassing executed without flux addition can increase the inclusion content of the melts. This can be attributed to the chemical reaction between the liquid alloy and the N2 purging gas during the degassing process. It was also found that inclusion content highly influences the tendency to porosity formation.

1 November 2021 in Materials Characterization
Verified
Journal Article
Open access
Gábor GyarmatiGábor Gyarmati
Gábor Gyarmati
GFGyörgy Fegyverneki
György Fegyverneki
ZKZoltán Kéri
Zoltán Kéri
DMDániel Molnár
Dániel Molnár
MTMonika Tokár
Monika Tokár
TMTamás Mende
Tamás Mende

17 January 2022 in Metallurgical and Materials Transactions B
Verified
Journal Article
Open access
PDF file
Gábor GyarmatiGábor Gyarmati
Gábor Gyarmati
FVFanni Vincze
Fanni Vincze
GFGyörgy Fegyverneki
György Fegyverneki
ZKZoltán Kéri
Zoltán Kéri
TMTamás Mende
Tamás Mende
DMDániel Molnár
Dániel Molnár
Rotary degassing is one of the most frequently used melt treatment technologies used for processing liquid aluminum alloys. Despite this, the information available about the possible effects of this method on the double oxide- and nitride film (bifilm) content, especially when using different purging gases, is quite limited. For this reason, in this study, the effects of multiple rotary degassing treatments conducted with N2 and Ar purging gases on the bifilm quantity of a casting aluminum alloy were compared. The characterization of the melt quality was realized by the computed tomographic (CT) analysis of reduced pressure test (RPT) specimens, image analysis, and scanning electron microscopy (SEM) of the fracture surfaces of K-mold samples. Based on the results, by the application of Ar as a purging gas, relatively low bifilm content can be achieved. On the other hand, while the use of N2 leads to the formation of numerous small-sized nitride bifilms, which significantly increased the pore number density inside the RPT specimens. This can be associated with the nitride formation by the chemical reaction between the liquid aluminum alloy and the N2 purging gas bubbles during the degassing treatments. Graphical abstract

1 November 2022 in Materials
Verified
Journal Article
Open access
PDF file
Gábor GyarmatiGábor Gyarmati
Gábor Gyarmati
LBLevente Bogoly
Levente Bogoly
Marcin StawarzMarcin Stawarz
Marcin Stawarz
GFGyörgy Fegyverneki
György Fegyverneki
ZKZoltán Kéri
Zoltán Kéri
TMTamás Mende
Tamás Mende
Grain refiner particles, which are intended to induce the formation of fine equiaxed grain structure during the solidification of aluminum alloys, are prone to settling during the holding of the liquid metal, which phenomenon can affect not only the grain size but the spatial distribution of the double oxide films in the melt. In this study, the settling of Al3Ti inoculant particles, as well as its effects on melt quality and grain refinement, were studied. During the experiments, the Ti-concentration of a liquid Al-Si-Mg-Cu alloy was increased to 0.3 wt.% by the addition of Al-10%Ti master alloy at different melt temperatures. Particle settling and grain size evolution were studied by quantitative metallography, while the interactions of grain refiners and bifilms were investigated by scanning electron microscopy (SEM). The evolution of melt quality was assessed by the computed tomographic (CT) analysis of reduced pressure test (RPT) samples. It was found that effective grain refinement was only realized when the introduced blocky Al3Ti particles were dissolved and re-precipitated in the form of (Al,Si)3Ti at a lower temperature. Without dissolving at higher holding temperatures, Al3Ti particle settling has taken place within 10 min. The settling of (Al,Si)3Ti particles improved melt quality by the aided sedimentation of bifilms in the melt.

1 July 2021 in Heliyon
Verified
Journal Article
Open access
Gábor GyarmatiGábor Gyarmati
Gábor Gyarmati
IBImre Budavári
Imre Budavári
GFGyörgy Fegyverneki
György Fegyverneki
LVLászló Varga
László Varga
The quality of chemically bonded sand cores used during the manufacturing process of cast components is highly dependent on the properties of the sand, which constitutes the refractory base media of the core. One of the main advantages of the application of different types of sands as molding aggregates that after casting, they can be reclaimed and can be used again during core shooting. The properties of the sand, however, could be remarkably changed during the casting and reclamation processes. This study aims to investigate the effects of the properties of the base sand on the mechanical strength and thermal distortion properties of samples made from new and thermally reclaimed silica sand. For this purpose, particle size analysis, specific surface area, and loss on ignition measurements, as well as differential thermal analysis coupled with thermogravimetry, were executed on the base sands, and the sand grains were analyzed with scanning electron microscopy and X-ray diffraction. Test pieces were made with hot box and cold box technology for bending and hot distortion tests. It was found that by the utilization of reclaimed sand, cores with higher average bending strength and lower thermal deformation can be produced. These differences can be traced back to the more advantageous granulometric properties, lower impurity content, and lower thermal expansion of thermally reclaimed sand.