Ev Hoşbaş

Dr. Ev Hoşbaş


Research Focus & Metrics

Academic Career Length

21Years (2006-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 February 2006 in Journal of Surveying Engineering
Verified
Journal Article
Closed access
GGGoknil Guler
Goknil Guler
HKHavvanur Kılıç
Havvanur Kılıç
EHEv Hoşbaş
Ev Hoşbaş
KOKutay Ozaydin
Kutay Ozaydin
In this study, the evaluation of the surface movements that took place after the completion of an earth fill dam constructed by staged construction have been evaluated by means of geodetic and geotechnical methods. Horizontal and vertical displacement measurements which were recorded between the years of 1987–1991 and 1991–1996 have been analyzed geodetically by using the Karlsruhe method. In both measurement periods, significant horizontal and vertical movements were found from adjustments and analyses of the measurements. The behavior of the dam and its foundation layers were analyzed by utilizing finite element method in two-dimensional plane-strain conditions to determine the horizontal and vertical surface movements. The results of geodetic measurements were compared with the results of the numerical analysis, and it is observed that there is a good agreement between the field measurements and computed values.

1 October 2009 in Survey Review
Verified
Journal Article
Closed access
APAtinc Pirti
Atinc Pirti
NANiyazi Arslan
Niyazi Arslan
BDB. Deveci
B. Deveci
OAO. Aydin
O. Aydin
HEH. Erkaya
H. Erkaya
EHEv Hoşbaş
Ev Hoşbaş

1 September 2011 in Acta Geodaetica et Geophysica Hungarica
Verified
Journal Article
Closed access
SHS. Hekimoglu
S. Hekimoglu
BEBahattin Erdogan
Bahattin Erdogan
RER. Erenoglu
R. Erenoglu
EHEv Hoşbaş
Ev Hoşbaş
Outliers in geodetic networks badly affect all parameters and their variances estimated by least-squares. Tests for outliers (e.g. Baarda’s and Pope’s tests) are frequently used to detect outliers in geodetic networks. To measure the ability of these tests, the mean success rate (MSR) is proposed. Studies have shown that the MSRs of these tests in geodetic networks are low due to the smearing effect of the least-squares estimation even if there is only one outlier in the data set. In this paper, a new approach, for small outliers, is presented to increase the MSRs of the tests for outliers in geodetic networks. The main idea is that if the weight of one observation is increased, the corresponding studentized or normalized residuals are increased, too. This thesis is proved. Hence, the ability of the tests to detect outliers can be increased by appropriately increasing the weight of one observation at a time and repeating this for all observations. This approach is applied to three simulated geodetic networks. We show that the MSRs of the outlier tests are improved by approximately 5% if there is one small outlier in the data set. However, the improvements in the MSRs for more than one outlier are low.

7 October 2022 in KSCE Journal of Civil Engineering
Verified
Journal Article
Open access
PDF file
APAtinc Pirti
Atinc Pirti
EHEv Hoşbaş
Ev Hoşbaş
MYMehmet Ali Yücel
Mehmet Ali Yücel
Izmir, which is one of the biggest cities of Turkey and has the extensive tectonic features of the Western Anatolia region, has been struck in recent years due to its high seismic activity. In particular, the south of Izmir is one of the regions that has high seismic activity in the city, which is constrained by major fault zones. The earthquake of magnitude of a Mw 6.9 occurred 8 km north of Samos Island at a depth of 16 km on 30.10.2020, at 11:51:24 UTC (14:51:24 Local Time (LT)). It occurred on a 40-kilometer-long north-dipping normal fault zone in the Mediterranean between Greece’s Samos Island and Turkey’s Kuşadası Bay. Following the mainschock, a tsunami with a height of more than 1 meter occurred at Sığacık Bay, south of Izmir, and on the north side of Samos Island. This article focuses on the investigation of the Samos earthquake by utilizing both GNSS data and InSAR images, and the obtained results are given in this paper. GNSS data were processed by using CSRS-PPP Software as static and kinematic modes. After processing the GNSS data, the maximum displacements were observed at CESME and IZMIR CORS-TR points located in the north of the fault. Horizontal movements of 12 cm and 6 cm towards the north were obtained at CESME and IZMIR points, respectively. However, the amount of horizontal movements was less at DIDIM and AYDIN CORS-TR locations, which are located to the south of the fault. In addition to GNSS data, ESA Sentinel-1 SAR data was used in the InSAR procedure, and the displacements were clarified using the unwrapped interferogram. The interferogram revealed a 10 cm uplift in the west of the Island of Samos and a 10 cm subsidence in the Izmir region, on the north side of the fault, based on the InSAR data. The most striking feature of this study is that the earthquake that occurred near the island of Samos was reported by Gansas’ study that the 3 GNSS points (SAMO, SAMU, and 093A) on the island of Samos are moving in a south direction and the largest displacement is about 36 centimetres south. However, in our study, the north direction is more prominent as the direction of movement at IZMIR and CESME points. The movement at the DIDIM point supports his work. In other words, the Samos Fault affected the points located in the north and south differently.

9 December 2019 in Geodesy and Cartography
Verified
Journal Article
Open access
PDF file
APAtinc Pirti
Atinc Pirti
EHEv Hoşbaş
Ev Hoşbaş
Applications in geodesy and engineering surveying require the determination of the heights of the vertical control points in the national and local networks using different techniques. These techniques can be classified as geometric, trigonometric, barometric and Global Positioning System (GPS) levelling. The aim of this study is to analyse height differences obtained from these three techniques using precise digital level and digital level, total station (trigonometric levelling) and GPS which collects phase and code observations (GPS levelling). The accuracies of these methods are analysed. The results obtained show that the precise digital levelling is more stable and reliable than the other two methods. The results of the three levelling methods agree with each other within a few millimetres. The different levelling methods are compared. Geometric levelling is usually accepted as being more accurate than the other methods. The discrepancy between geometric levelling and short range trigonometric levelling is at the level of 8 millimetres. The accuracy of the short range trigonometric levelling is due the reciprocal and simultaneous observations of the zenith angles and slope distances over relative short distances of 250 m. The difference between the ellipsoidal height differences obtained from the GPS levelling used without geoid and the orthometric height differences obtained from precise geometric levelling is 4 millimetres. The geoid model which is obtained from a fifth order polynomial fit of the project area is good enough in this study. The discrepancy between the precise geometric and GPS levelling (with geoid corrections) is 4 millimetres over 5 km.

30 April 2016 in Šumarski list
Verified
Journal Article
Open access
PDF file
APAtinc Pirti
Atinc Pirti
EHEv Hoşbaş
Ev Hoşbaş
TOTaylan Ocalan
Taylan Ocalan
NTNursu Tunalioglu
Nursu Tunalioglu
Apsolutno određivanje položaja točke s GNSS/CORS (Globalni navigacijski satelitski sustav) u šumskim područjima predstavlja značajan izazov u smislu uštede vremena, kako bi se dobile što točnije koordinate točaka. Vrijeme za rješenje neodređenosti faze cijelih brojeva nosača obično traje jedan sat ili više za apsolutno određivanje točaka pod šumskim područjem s GNSS/CORS. U ovom istraživanju predložena je alternativna metoda za određivanje položaja točke, koja daje rezultate položaja s preciznošću na razini centimetra i potrebno je skoro 15 minuta kako bi se dala nova lokacija točke u šumskom području. Predložena metoda može također imati praktičnu primjenu za unutarnje prostore sa željenom preciznošću na razini cm, koja se postiže u kratkom vremenu promatranja. U ovom istraživanju, proveli smo terenski rad kako bi dobili koordinate točaka u šumskim područjima s GNSS/CORS sustavom i dodatnim mjerenjima, utvrđivanjem dviju kontrolnih točaka promatranih s GNSS/CORS lociranih na granici šumskog područja. Rezultati pokazuju da se zadovoljavajuće rješenje za šumsko područje postiže na razini cm (≈ ± 6 cm) u kratkom vremenu promatranja.