Cu2O homojunction solar cells were fabricated using potentiostatic electrodeposition technique. n-Cu2O thin films were grown in an acetate bath while p-Cu2O thin films were grown in a lactate bath. In the growth of n-Cu2O films, cupric acetate concentration, pH and temperature of the bath, deposition potential and duration (film thickness) and annealing temperature were investigated. In the growth of p-Cu2O on n-Cu2O, concentration of copper sulphate and lactic acid solutions, pH and temperature of the bath, deposition potential and duration were investigated. In addition, the procedure of sulfidation of p-Cu2O film surface using (NH4)2S vapor, before depositing Au front contact, was also optimized to enhance the photoactive performance. The structural, morphological and optoelectronic properties of the Cu2O films were investigated using scanning electron microscopy (SEMs), high energy X-ray diffraction (HEXRD), hard X-ray photoelectron spectroscopy (HAXPES), spectral response and current–voltage (J-V) measurements. The best Cu2O homojunction solar cell exhibited Voc = 460 mV, Jsc = 12.99 mA·cm−2, FF = 42% and η = 2.51%, under AM 1.5 illumination. Efficiency enhancement with the record high Jsc value for the Cu2O homojunction solar cell has mainly been due to the optimization of pH of the n-Cu2O deposition bath and lactic acid concentration of the p-Cu2O deposition bath.
Improvements in electrodeposited cuprous oxide (Cu2O) junction devices could contribute to development of a wider range of affordable and environmentally friendly electronic devices. In this regard, ability of controlling interfacial properties of contacts of Cu2O thin films with other suitable materials will be a very important property. A study on interfacial properties of p-Cu2O/Au and p-Cu2O/electrolyte junctions was conducted using capacitance-voltage and current-voltage measurements. It was found that pH of p-Cu2O film deposition bath has a significant effect on junction properties of Cu2O. Particularly, flat band potential at p-Cu2O/electrolyte interface and built-in potential at p-Cu2O/Au interface were shifted positively by the increase of deposition bath pH of p-Cu2O films. Also, it was revealed that the shift was more pronounce at p-Cu2O/Au interface compared to that at p-Cu2O/electrolyte interface. The observed shifts in flat band potential and built in potentials were correlated with the shifts in relative band edge positions at the interfaces and with the change in net surface charge on the interfacial layers. It was observed, for the first time, that built in potential at p-Cu2O/Au junction can be controlled with bath pH of p-Cu2O films so that the junction can make either ohmic or non ohmic. Further, it was found that surface modification of p-Cu2O films with sulphidation reduces barrier height at p-Cu2O/Au junction and make the contact ohmic irrespective of bath pH of p-Cu2O films. We report here, for the first time, that relative band edge position at interfaces of electrodeposited p-Cu2O junctions can be controlled with pH of film deposition bath and surface modification. This will be very useful in application of electrodeposited p-Cu2O thin films in solar cells and other junction devices.
30 April 2021 in Journal of the National Science Foundation of Sri Lanka
The rapid global population growth and technological transition have enhanced daily energy demands. This poses significant challenges to energy production from fossil fuels, whose reserves are finite. Solar energy offers a sustainable, renewable solution to the prevailing energy production issues. Photovoltaic energy, in particular, is favorable due to its widespread availability, free accessibility, eco-friendly nature, and low operational and maintenance costs. However, the available photovoltaics are expensive and unaffordable to the general public. This study focuses on the development of a low-cost eco-friendly SnO2/Cu2O heterojunction solar cell by the method of electrodeposition. The fabrication process involved the electrodeposition of an n-type SnO2 thin film onto copper substrates, followed by the subsequent electrodeposition of p-type Cu2O thin film. The photoresponse of the solar cell structured Cu/SnO2/Cu2O/Au was optimized by tuning the bath temperature during SnO2 thin film deposition. Structural, morphological, and optoelectronic properties were systematically investigated using X-ray diffraction (XRD), scanning electron microscopy (SEM), and current–voltage (I–V) measurements. Under AM 1.5G illumination at 100 mW/cm², the optimized device exhibited an open-circuit voltage (Voc) of 156.26 mV, a short-circuit current density (Jsc) of 1.09 mA/cm², a fill factor (FF) of 27.80%, and a power conversion efficiency (η) of 0.047%. Although the efficiency is relatively low, the results are promising due to the use of earth-abundant, non-toxic materials, low-temperature electrodeposition, and the clear potential for further performance enhancement through interface engineering.
24 August 2026 in Journal of Materials Science: Materials in Electronics