Cuprous oxide (Cu2O) homojunction thin films on Ti substrates were fabricated by an electrochemical deposition in which a p-Cu2O layer was deposited on an n-Cu2O layer by carefully controlled bath conditions. It was found that the open-circuit voltage of the homojunction solar cell was significantly influenced by the pH of the lactate bath. The variation of the pH was used to achieve the best possible crystal orientation for homojunctions. The crystallinity and morphology of the products were characterized by X-ray diffraction (XRD), high-energy x-ray diffraction (HEXRD), and scanning electron microscopy (SEM). The current density voltage (J-V) analysis showed that the sulfur treatment and annealing enhanced the photocurrent by ten-fold compared to the untreated and unannealed homojunction solar cell. X-ray photoelectron spectroscopy (XPS) studies confirmed that the sulfur treatment eliminated the surface CuO and formed a thin layer of CuS, which was very useful to make the front Ohmic contact. Transient measurements confirmed that the p-type Cu2O layer, which was subjected to sulfur treatment, significantly reduced the recombination, thus enhancing the efficiency of the solar cell. The best sulfur treated annealed Ti/n-Cu2O/p-Cu2O/Au solar cell produced an energy conversion efficiency of 2.64% with an open-circuit voltage of 490 mV and a short circuit current density of 12.8 mA cm−2 under AM 1.5 illumination.
12 November 2012 in Semiconductor Science and Technology
CuO was synthesized by employing the facile chemical precipitation technique to vary the concentrations of Cu(NO3)2 in a range from 0.001 to 0.1 M. This was carried out in order to find the concentration of Cu(NO3)2 that results in optimal electrochemical performance in CuO as an anode electrode material for lithium-ion batteries. Among the investigated concentrations, the 0.03 M Cu(NO3)2 showed the best electrochemical performance. Of the synthesized materials, the scanning electron microscopic (SEM) analysis revealed the existence of a sponge-like morphology. X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), synchrotron X-ray diffraction (SXRD) and Raman spectrum confirmed the formation of a required CuO phase. The electron density distribution on the crystalline structure of the synthesized CuO indicates the existence of the highest distribution of electrons around Cu atoms, with enhanced productivity of the conversion mechanism during the cycling process. Further, this study shows that the electronic interfacial properties of Cu/CuO could be improved by optimizing the amount of acetylene black used for the electrode fabrication, with 20 wt% being the optimum value. The electrodes fabricated with the synthesized sponge-like microstructured CuO as the active material exhibited a high initial specific discharge capacity of 3371.9 mA h g−1 and resulted in a specific discharge capacity of 442.9 mA h g−1 (Coulombic efficiency of 97.4%) after 50 cycles, at a rate of 0.2 C. Moreover, the specific discharge capacity reported at the rate of 1.0 C was 217.6 mA h g−1 with a significantly high Coulombic efficiency of about 98.0% after 50 cycles. Altogether, this study reveals the high potentiality of using sponge-like microstructured CuO as a high-performance anode electrode material for LIBs.
Cu2O homojunction solar cells were fabricated using potentiostatic electrodeposition technique. n-Cu2O thin films were grown in an acetate bath while p-Cu2O thin films were grown in a lactate bath. In the growth of n-Cu2O films, cupric acetate concentration, pH and temperature of the bath, deposition potential and duration (film thickness) and annealing temperature were investigated. In the growth of p-Cu2O on n-Cu2O, concentration of copper sulphate and lactic acid solutions, pH and temperature of the bath, deposition potential and duration were investigated. In addition, the procedure of sulfidation of p-Cu2O film surface using (NH4)2S vapor, before depositing Au front contact, was also optimized to enhance the photoactive performance. The structural, morphological and optoelectronic properties of the Cu2O films were investigated using scanning electron microscopy (SEMs), high energy X-ray diffraction (HEXRD), hard X-ray photoelectron spectroscopy (HAXPES), spectral response and current–voltage (J-V) measurements. The best Cu2O homojunction solar cell exhibited Voc = 460 mV, Jsc = 12.99 mA·cm−2, FF = 42% and η = 2.51%, under AM 1.5 illumination. Efficiency enhancement with the record high Jsc value for the Cu2O homojunction solar cell has mainly been due to the optimization of pH of the n-Cu2O deposition bath and lactic acid concentration of the p-Cu2O deposition bath.
The surging prevalence of diabetes globally necessitates advancements in non-invasive diagnostics, particularly for the early detection of cardiovascular anomalies associated with the condition. This study explores the efficacy of Pulse Wave Analysis (PWA) for distinguishing diabetic from non-diabetic individuals through morphological examination of pressure pulse waveforms. The research unfolds in four phases: data accrual, preprocessing, Convolutional Neural Network (CNN) model construction, and performance evaluation. Data were procured using a multipara patient monitor, resulting in 2000 pulse waves equally divided between healthy individuals and those with diabetes. These were used to train, validate, and test three distinct CNN architectures: the conventional CNN, Visual Geometry Group (VGG16), and Residual Networks (ResNet18). The accuracy, precision, recall, and F1 score gauged each model’s proficiency. The CNN demonstrated a training accuracy of 82.09% and a testing accuracy of 80.6%. The VGG16, with its deeper structure, surpassed the baseline with training and testing accuracies of 90.2% and 86.57%, respectively. ResNet18 excelled, achieving a training accuracy of 92.50% and a testing accuracy of 92.00%, indicating its robustness in pattern recognition within pulse wave data. Deploying deep learning for diabetes screening marks progress, suggesting clinical use and future studies on bigger datasets for refinement.
Improving the performance of TiO2 photoanodes via the inclusion of metal particles on the electrode surface could provide significant advantages for the development of dye-sensitized solar cells (DSSCs). We studied a TiO2/Cu film electrode prepared by electrodepositing Cu particles on a TiO2 film on an indium-doped tin oxide (ITO) substrate. Cu particles were electrodeposited on a TiO2 electrode at −700 mV vs. a Ag/AgCl electrode in an acetate bath, with the pH adjusted between 6.3 and 7.7 in 0.2 increments to optimize the deposition conditions. TiO2/Cu thin-film electrodes were tested as a photo anode in a natural DSSC consisting of a carbon counter electrode, Vitis vinifera dye, and a KI/I2-based electrolyte. Film characterization was performed using hard X-ray photoelectron spectroscopy (HAXPES), grazing incidence X-ray diffraction (GIXD), scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy, electrochemical impedance spectroscopy (EIS), ultraviolet–visible spectroscopy (UV–Vis), and photocurrent density–voltage (J–V) measurements. DSSCs with Cu particles containing TiO2 electrodes prepared using an acetate bath of pH 7.3 resulted in a 370% improvement in efficiency compared to the DSSCs without Cu particles. Thus, this study revealed that incorporating Cu particles into the surface of the TiO2 electrode enhances the photovoltaic performance of DSSCs.