Ciro Santus

Prof. Ciro Santus

DICI - Dept. of Civil and Inustrial Engineering, University of Pisa, Pisa, Tuscany, Italy
orcid

Research Focus & Metrics

Academic Career Length

23Years (2004-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 June 2012 in Metallurgical and Materials Transactions A
Verified
Journal Article
Closed access
PDF file
GLGianfranco Lovicu
Gianfranco Lovicu
MBMauro Bottazzi
Mauro Bottazzi
FDFabio D’aIuto
Fabio D’aIuto
MSMassimo De Sanctis
Massimo De Sanctis
ADAntonella Dimatteo
Antonella Dimatteo
RVRenzo Valentini
Renzo Valentini

1 August 2009 in International Journal of Fatigue
Verified
Journal Article
Open access
Ciro SantusCiro Santus
Ciro Santus
DTD. Taylor
D. Taylor
In metals, during high cycle fatigue on plain specimens, almost the entire fatigue life is spent as short crack initiation and propagation. The fatigue short crack life can be schematically divided into two subsequent phases: microstructurally short crack and physically short crack. Recently, Chapetti proposed a physically short crack threshold and propagation driving force model [Chapetti MD. Fatigue propagation threshold of short cracks under constant amplitude loading. Int J Fatigue 2003;25(12):1319–1326]. In his model the physically short crack behavior is obtained from the long crack propagation, just introducing the reduced threshold due to unsaturated closure. In the present paper the physically short crack propagation is similarly modeled by means of a driving force equation, but independent from the long crack propagation. In this way, a better description of the short crack behavior is provided, however short crack propagation data is required. Physically short crack propagation model parameters were obtained, by fitting experimental data drawn from the literature, for two aluminum alloys and a titanium alloy at two different heat treatment conditions and load ratios. By calculating the physically short crack plus long crack propagation, and assuming microstructurally short crack as part of the initiation stage, a purer information about crack initiation can be drawn from the S – N curves, and it is shown in the paper for the investigated materials. A precise crack initiation size and the number of cycles just for initiation are then provided. This information is useful to accurately predict fatigue life for blunt notched and for thick components, where the propagation is much higher than in the small plain specimen. A validation of the model was obtained by predicting the fatigue life of a notched specimen. An accurate prediction was obtained both when the initiation was much smaller than propagation and when almost the entire fatigue life was initiation.


1 October 2010 in International Journal of Fatigue
Verified
Journal Article
Closed access
MBM. Benedetti
M. Benedetti
Vigilio FontanariVigilio Fontanari
Vigilio Fontanari
Ciro SantusCiro Santus
Ciro Santus
MBM. Bandini
M. Bandini

1 December 2012 in International Journal of Fatigue
Verified
Journal Article
Open access
Ciro SantusCiro Santus
Ciro Santus
MBM. Beghini
M. Beghini
IBI. Bartilotta
I. Bartilotta
MFM. Facchini
M. Facchini
The rolling contact fatigue is distinguished into subsurface initiated (spalling and case crushing) and surface initiated (pitting and micropitting). A characteristic depth was identified for each of these mechanism. The characteristic depth of the case crushing is the hardening depth, while for the spalling it is the maximum cyclic shear stress depth. The pitting depth is the size of the crack for which the mode I stress intensity factor range, due to the fluid pressurization, is higher than the threshold. This depth can be similar to the micropitting depth, in the order of 10 µm, for heavily loaded small radius contacts. Rolling contact fatigue cyclic shear stress indexes are then defined on the basis of the characteristic depths, and they identify the load intensity of each rolling contact fatigue mechanism. The characteristic depths and the stress index approach can be used to relate specific tests to component design, without any size effect misinterpretation

1 December 2015 in International Journal of Fatigue
Verified
Journal Article
Closed access
LBL. Bertini
L. Bertini
Ciro SantusCiro Santus
Ciro Santus