Do-Yun Kim

Prof. Do-Yun Kim

orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
31 July 2020 in Energies
Verified
Journal Article
Open access
PDF file
DKDo-Yun Kim
Do-Yun Kim
JLJung-Hyo Lee
Jung-Hyo Lee
This paper proposes a permanent magnet synchronous machine (PMSM) table-based torque control method considering a variable DC-link voltage that can be used in a low cost DSP. The current reference generation based on two-dimensional look-up table (2D-LUT) is widely used for PMSM drives used in industrial applications because of its torque control performance and operation stability. In general, a 2D-LUT is established based on the flux and torque to overcome the variation in DC-link voltage. However, this method requires a flux estimator for estimating the instantaneous flux, which is defined as a division of the operating speed used to obtain the flux data. Therefore, to obtain the operating flux, a variable division calculation or complex controller is used, which can be difficult to process through a low cost digital signal processor. In this paper, a novel look-up table-based control method that uses the newly established speed-torque 2D-LUT is proposed. This 2D-LUT inherently implements data on the d-/q-axis currents throughout the operating regions, not only the speed and torque, but also the DC-link voltage variation. The proposed method was verified through an experiment on the torque control a variation in the DC-link voltage.

4 September 2021 in Energies
Verified
Journal Article
Open access
PDF file
DKDo-Yun Kim
Do-Yun Kim
JLJung-Hyo Lee
Jung-Hyo Lee
This paper proposes a compensation method for interpolation error of the maximum power control of a PMSM control system that generates current commands through a look-up table. A torque control system using a look-up table created through experiments has superior characteristics, such as control stability and torque accuracy, compared to a system that executes torque control via a linear controller based on modeling. However, it is impossible to generate information on all the currents for the output torque in the table. Therefore, because the data stored in the look-up table have a discrete characteristic, they are linearly interpolated to generate a current command for the torque command. However, the PMSM current trajectory is generally elliptical, which causes an error owing to linear interpolation, reducing the maximum output power. In particular, when the table data are insufficient, such as in the high-speed operation range, the reduced maximum output cannot be ignored. This paper proposes a compensation method for the interpolation error using two feedforward compensators and a PI controller, which was verified through experiments.

10 July 2021 in Electronics
Verified
Journal Article
Open access
PDF file
MKMun-Hong Kim
Mun-Hong Kim
DKDo-Yun Kim
Do-Yun Kim
It is necessary to obtain the rotor position of the Interior Permanent Magnet Synchronous Motor (IPMSM) for instantaneous torque control in an electric vehicle system. A resolver is mostly used as a rotor position sensor, each motor has a resolver offset according to the fit tolerance of the resolver pressed into the rotor shaft when the motor is manufactured. This resolver offset is having a huge effect on IPMSM output characteristics. Therefore, resolver offset detection equipment with a method for high precision of detection is required in production lines in order to make uniform characteristics of IPMSM. It is also necessary to have robust performance in many different kinds of the noise of equipment in the production line. This paper presents a highly precise Resolver to Digital Converter (RDC) that is implemented with LabVIEW of National Instruments and a resolver offset detecting method that has the robust performance to noise based on coordinate transformation algorithm. Experiments with and without the proposed method were performed and a comparative analysis is conducted to test the validity.

23 November 2024 in World Electric Vehicle Journal
Verified
Journal Article
Open access
PDF file
DKDo-Yun Kim
Do-Yun Kim
This study investigates the efficiency and noise, vibration, and harshness (NVH) characteristics of electric vehicle (EV) powertrains based on three key Pulse Width Modulation (PWM) techniques: Space Vector PWM (SVPWM), Discontinuous PWM (DPWM), and Random PWM (RPWM). The objective is to evaluate the impact of these PWM techniques on inverter and motor efficiency, as well as their effects on NVH performance, particularly in relation to noise and vibration. Experiments were conducted across various speed and torque levels using a motor dynamo. The study reveals that DPWM provides the highest efficiency, outperforming SVPWM by up to 2.23%. However, DPWM introduces more noise due to increased total harmonic distortion (THD), negatively affecting NVH performance. SVPWM, on the other hand, offers a balanced trade-off between efficiency and NVH, while RPWM demonstrates comparable noise characteristics to SVPWM, with potential for broader harmonic distribution. The findings suggest that each PWM technique offers distinct advantages, and their selection should depend on the required balance between efficiency and NVH.