Katarína Bernátová

Ms. Katarína Bernátová

orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 May 2020 in Plasma Sources Science and Technology
Verified
Journal Article
Closed access
KBKatarína Bernátová
Katarína Bernátová
MFM Fekete
M Fekete
PKP Klein
P Klein
JHJ Hnilica
J Hnilica
PVP Vašina
P Vašina
In this paper, the ground state number densities of titanium atom and ion, ionised density fraction and ionised flux fraction were determined in a high power impulse magnetron sputtering process. Three regions of interest within the deposition chamber were studied; the magnetised plasma region, middle region, and substrate region. Pulse length and applied power were kept constant and working pressure and duty cycle were varied. The effective branching fractions method was utilised to evaluate the number densities of sputtered species from a measured optical emission signal. A biasable quartz crystal microbalance system was used to evaluate the ionised flux fraction and deposition rate. The highest ionised density fraction of 90% was reached in the target region for 1.2% duty cycle and it was mostly independent on working pressure. Moving from the target, the ionised density fraction was observed to decrease. In the substrate region for a duty cycle below 2% and the whole studied working pressure range, the ionised density fraction always reached at least 50%.

8 July 2020 in Materials
Verified
Journal Article
Open access
PDF file
LZLukáš Zábranský
Lukáš Zábranský
KBKatarína Bernátová
Katarína Bernátová
JDJiří Dluhoš
Jiří Dluhoš
RVRostislav Váňa
Rostislav Váňa
PSPavel Souček
Pavel Souček
VBVilma Bursikova
Vilma Bursikova
This research was devoted to studying the influence of the taper angle on the micro-compression of micro-pillars fabricated from near-amorphous and nanocrystalline Mo-B-C coatings. A series of micro-pillars with a taper angle between 4–14° was fabricated by focused ion beam technique. The deformation mechanism was found to be dependent on the taper and, also, on the crystallinity of the coating. In order to obtain correct values of yield strength and Young’s modulus, three empirical models of stress correction were experimentally tested, and the results were compared with nanoindentation measurements. It was shown that the average stress correction model provided comparable results with nanoindentation for the yield strength for taper angles up to ~10°. On the other hand, the average radius or area model gave the most precise results for Young’s modulus if the taper angle was <10°.

1 December 2021 in Plasma Sources Science and Technology
Verified
Journal Article
Closed access
PDF file
KBKatarína Bernátová
Katarína Bernátová
PKP Klein
P Klein
JHJ Hnilica
J Hnilica
PVP Vašina
P Vašina
Temporal evolutions of the ground state number densities of titanium atoms and ions and the ionised density fraction during pulse on-time are experimentally investigated for the high-power impulse magnetron sputtering process in an Ar and Ar/N 2 atmosphere. For the study, two distinct pulses with the same pulse length at a constant average power but different pulse off-times were selected. In both conditions, four representative points within the hysteresis curve were chosen, and the time evolutions of sputtered species densities were investigated in both the target and the substrate regions. At the pulse beginning, a high density of residual particles sputtered during the previous pulse is present in both studied regions. In the target region, in conditions of longer pulse off-time and thus higher peak discharge current, 95% of sputtered particles are ionised in metallic, transition and compound regimes. With shorter pulse off-time conditions, and thus a lower peak discharge current, the ionised density fraction is the lowest in the metallic regime; in the transition and compound regimes, it exceeds 80%. In the substrate region, the temporal evolution of sputtered species densities differs from that obtained in the target region. After the pulse ignition, titanium atoms and ions remaining near the substrate from the previous pulse are pushed away. In the metallic regime, the sputtered atoms refill the substrate region already during the pulse on-time in both the low- and high-current conditions. In the high-current conditions, the titanium ions arrive at the substrate together with the sputtered atoms; however, in the low-current conditions, the titanium ion density decreases during the pulse on-time, and the titanium ions arrive later during the pulse off-time. In the transition and compound regimes, both densities steadily decrease during the pulse on-time and the titanium atoms and ions arrive at the substrate during the pulse off-time.