Lukáš Zábranský

Dr. Lukáš Zábranský

orcid

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
8 August 2016 in The European Physical Journal Applied Physics
Verified
Journal Article
Closed access
PDF file
LZLukáš Zábranský
Lukáš Zábranský
VBVilma Bursikova
Vilma Bursikova
PSPavel Souček
Pavel Souček
PVPetr Vašina
Petr Vašina
JBJiří Buršík
Jiří Buršík
Mo2BC thin films show a favourable combination of high stiffness, hardness and elastic modulus together with moderate ductility. In this study we focused on the comparison of mechanical properties of Mo-B-C thin films with different structures (nanocrystalline or amorphous). The thin films were deposited on steel, hard metal and silicon substrates using DC magnetron sputtering. The mechanical properties of Mo-B-C films were studied using indentation techniques under both quasistatic and dynamic conditions using a wide range of loads from 50 μN up to 1 N. The results showed that even amorphous Mo-B-C thin films had high hardness of 19.5 ± 0.5 GPa and elastic modulus of 276 ± 5 GPa. Their hardness is comparable with the common amorphous diamond-like carbon coatings. Moreover, their fracture toughness is significantly higher. The results of mechanical tests were correlated with microstructure observations carried out using scanning and transmission electron microscopy. The images of the deformed area under the residual indentation imprints showed no cracking even after high loads or after indentation with sharp cube corner indenter.

14 March 2018 in Journal of Nanomaterials
Verified
Journal Article
Open access
PDF file
PSPavel Soucek
Pavel Soucek
LZLukáš Zábranský
Lukáš Zábranský
VBVilma Bursikova
Vilma Bursikova
JBJiri Bursik
Jiri Bursik
SDStanislava Debnarova
Stanislava Debnarova
PVPetr Vasina
Petr Vasina
State-of-the-art protective coatings often suffer from brittleness. Therefore, the coatings are intensively sought which would simultaneously exhibit high hardness and stiffness with moderate ductility and fracture resistance. In this paper, we report on the nanostructure designing of coatings containing metal, boron, and carbon enabling the simultaneous presence of stiff boridic and carbidic bonds together with weaker metallic bonds to provide coatings with these desirable properties. Three designs are presented with different relative amounts of nanocrystalline and amorphous phases, ranging from near-amorphous to prevalently crystalline microstructure. All presented coatings exhibit an unusual combination of high fracture resistance and high hardness that cannot be achieved with state-of-the-art protective coatings. Indentation tests at high loads revealed that no cracks are present at the surface of the investigated coatings while state-of-the-art ceramic protective coatings already exhibit significant cracking. Cracks in the bulk of the presented coating are detected only when the deformation is so severe that the substrate itself fails.

8 July 2020 in Materials
Verified
Journal Article
Open access
PDF file
LZLukáš Zábranský
Lukáš Zábranský
KBKatarína Bernátová
Katarína Bernátová
JDJiří Dluhoš
Jiří Dluhoš
RVRostislav Váňa
Rostislav Váňa
PSPavel Souček
Pavel Souček
VBVilma Bursikova
Vilma Bursikova
This research was devoted to studying the influence of the taper angle on the micro-compression of micro-pillars fabricated from near-amorphous and nanocrystalline Mo-B-C coatings. A series of micro-pillars with a taper angle between 4–14° was fabricated by focused ion beam technique. The deformation mechanism was found to be dependent on the taper and, also, on the crystallinity of the coating. In order to obtain correct values of yield strength and Young’s modulus, three empirical models of stress correction were experimentally tested, and the results were compared with nanoindentation measurements. It was shown that the average stress correction model provided comparable results with nanoindentation for the yield strength for taper angles up to ~10°. On the other hand, the average radius or area model gave the most precise results for Young’s modulus if the taper angle was <10°.

27 October 2022 in Vacuum
Verified
Journal Article
Open access
ŠKŠtěpánka Kelarová
Štěpánka Kelarová
RPRoman PřIbyl
Roman PřIbyl
VHVojtěch Homola
Vojtěch Homola
JPJosef Polčák
Josef Polčák
ACAnna Charvátová Campbell
Anna Charvátová Campbell
VBVilma Bursikova
Vilma Bursikova

1 March 2014 in Surface and Coatings Technology
Verified
Journal Article
Closed access
LZLukáš Zábranský
Lukáš Zábranský
VBV. Buršíková
V. Buršíková
PSP. Souček
P. Souček
PVP. Vašina
P. Vašina
TGT. Gardelka
T. Gardelka
JBJ. Buršík
J. Buršík

31 August 2020 in Coatings
Verified
Journal Article
Open access
PDF file
MKMichael Kroker
Michael Kroker
PSPavel Souček
Pavel Souček
PMPavol Matej
Pavol Matej
LZLukáš Zábranský
Lukáš Zábranský
Zsolt CziganyZsolt Czigany
Zsolt Czigany
PVPetr Vašina
Petr Vašina
Ta–B–C coatings were non-reactively sputter-deposited in an industrial batch coater from a single segmented rotating cylindrical cathode employing a combinatorial approach. The chemical composition, morphology, microstructure, mechanical properties, and fracture resistance of the coatings were investigated. Their mechanical properties were linked to their microstructure and phase composition. Coatings placed stationary in front of the racetrack of the target and those performing a 1-axis rotation around the substrate carousel are compared. Utilization of the substrate rotation has no significant effect on the chemical composition of the coatings deposited at the same position compared to the cathode. Whereas the morphology of coatings with corresponding chemical composition is similar for stationary as well as rotating samples, the rotating coatings exhibit a distinct multilayered structure with a repetition period in the range of nanometers despite utilizing a non-reactive process and a single sputter source. All the coatings are either amorphous, nanocomposite or nanocrystalline depending on their chemical composition. The presence of TaC, TaB, and/or TaB2 phases is identified. The crystallite size is typically less than 5 nm. The highest hardness of the coatings is associated with the presence of larger grains in a nanocomposite structure or formation of polycrystalline coatings. The number, density, and length of cracks observed after high-load indentation is on par with current optimized commercially available protective coatings.