Nanotechnology is widely recognized for having important applications in many industries, one of which is oil and gas. Both environmental and cost benefits can be achieved when using nanoparticles for the separation of water and oil or further purification of produced water. More efficient emulsion separation can be achieved by selective adsorption of naturally present stabilizing components or magnetic action applied to nanoparticle-tagged droplets. The focus of this review is given to both nanoparticles and nanocomposites that have been studied with respect to asphaltene adsorption, crude oil demulsification, and produced water treatment, as well as oil spill cleanup and improvement of antifouling resistance of filtration membranes. Asphaltene chemistry and its role in emulsion stabilization are discussed in detail.

The development of floating photovoltaic systems (FPV) for coastal and offshore locations requires a solid understanding of a design’s hydrodynamic performance through reliable methods. This study aims to extend insights into the hydrodynamic behavior of a superficial multi-body FPV system in mild and harsh wave conditions through basin tests at scale 1:10, with specific interest in the performance of hinges that interconnect the PV panels. Particular effort is put into correctly scaling the elasticity of the flexible hinges that interconnect the PV modules. Tests of a 5 × 3 FPV matrix are performed, with and without shelter, by external floating breakwater (FBW). The results show that the PV modules move horizontally in the same phase when the wave length exceeds the length of the FPV system, but shorter waves result in relative motions between modules and, for harsh seas, in hinge buckling. Relative motions suggest that axial loads are highest for the hinges that connect the center modules in the system and for normal wave incidence, while shear loads are highest on the outward hinges and for oblique incidence. The FBW reduces hinge loads as it attenuates the high-frequency wave energy that largely drives relative motions between PV modules.

Propellers are a vital component to achieve successful and reliable operation of drones. However, the drone developer faces many challenges while selecting a propeller and a common approach is to perform static thrust measurement. However, the selection of a propeller using a static thrust measurement system is time-consuming. To overcome a need for the static thrust system a virtual model has been developed for measuring both the static and dynamic thrust of a single and coaxial propeller. The virtual model is reliable enough to minimize the need for full-scale tests. The virtual model has been built using two open-source software Qblade and OpenFoam. Qblade is employed to obtain the lift and drag coefficients of the propeller’s airfoil section. OpenFoam is utilized to perform the flow simulations of propellers and for obtaining the thrust and torque data of the propeller. The developed virtual model is validated with experimental data and the experimental data are obtained by developing a multi-force balance system for measuring thrusts and torques of a single and a pair of coaxial contra-rotating propellers. The data obtained from the propeller virtual model are compared with the measurement data. For a single propeller, the virtual model shows that the estimated forces are close to the experiment at lower rotational speeds. For coaxial propellers, there are some deviations at the rear propeller due to the turbulence and flow disturbance caused by the front propeller. However, the computed thrust data are still accurate enough to be used in selecting the propeller. The studies indicate that in the future, these virtual models will minimize a need for experimental testing.

In the present research paper modeling principles for the oil-water separation with special emphasis on the modeling of dense packed layer (DPL) is presented. Formation of the DPL is attributed to the difference between sedimentation rate and interfacial coalescence rate. Different submodels resolving for the free sedimentation zone, the DPL, the binary coalescence, and the interfacial coalescence are described. These submodels are implemented in commercial CFD software. Adequate validation and calibration of these submodels are necessary to be used for understanding the separation processes in industrial separators. Experiments for understanding the water-in-oil separation processes in a horizontal continuous separator were designed and carried out. Results from bottle and decay tests were used only for calibrating the model. CFD simulations using the calibrated model have served to understand the flow phenomena occurring inside the horizontal separator. The prediction of the model seems to be satisfactory except at higher emulsion flow rate and lower water cuts. GRAPHICAL ABSTRACT

Offshore floating photovoltaic (FPV) systems are subjected to significant aerodynamic forces, especially during extreme wind conditions. Accurate estimation of these forces is crucial for the proper design of mooring lines and connection systems. In this study, detailed CFD simulations were performed for various PV panel configurations, and using these CFD simulation correlations were developed to estimate lift and drag forces as a function of the number of panels. These correlations provide valuable tools for designing large-scale FPV systems with multiple PV modules. Additionally, this study investigates the potential of using breakwaters to reduce aerodynamic forces on FPV systems. Breakwaters, typically used to mitigate wave impacts, can also serve as wind barriers, significantly reducing wind forces before they reach the FPV array. Aerodynamic simulations with and without a breakwater were conducted using CFD to assess this effect. The results show a substantial reduction in lift and drag coefficients, especially for angles of attack up to 10 degrees, demonstrating the effectiveness of the breakwater in protecting the FPV system. However, beyond this threshold, the effectiveness of the breakwater of 2 m reduces. These findings highlight the importance of strategic breakwater placement and heights and their role in enhancing FPV system resilience. The insights gained from this study are critical for optimizing breakwater design and placement, ensuring the structural integrity and performance of FPV systems in varying environmental conditions. The data generated will also contribute to future design improvements for floating PV systems.