The use of micro fibres in Ultra-High-Performance Concrete (UHPC) as reinforcement increases tensile strength and especially improves the post-cracking behaviour. Without using fibres, the dense structure of the concrete matrix results in a brittle failure upon loading. To counteract this behaviour by fibre reinforcement, an optimal bond between fibre and cementitious matrix is essential. For the composite properties not only the initial surfaces of the materials are important, but also the bonding characteristics at the interfacial transition zone (ITZ), which changes upon the joining of both materials. These changes are mainly induced by the bond of cementitious phases on the fibre. In the present work, three fibre types were used: steel fibres with brass coating, stainless-steel fibres as well as nickel-titanium shape memory alloys (SMA). SMA fibres have the ability of “remembering” an imprinted shape (referred to as shape memory effect), triggered by thermal activation or stress, principally providing for superior performance of the fibre-reinforced UHPC. However, previous studies have shown that NiTi-fibres have a much lower bond strength to the concrete matrix than steel fibres, eventually leading to a deterioration of the mechanical properties of the composite. Accordingly, the bond between both materials has to be improved. A possible strategy is to roughen the fibre surfaces to varying degrees by laser treatment. As a result, it can be shown that laser treated fibres are characterised by improved bonding behaviour. In order to determine the bond strength of straight, smooth fibres of different metal alloy compositions, the present study characterized multiple fibres in series with a Compact-Tension-Shear (CTS) device. For critical evaluation, results obtained by these tests are compared with the results of conventional testing procedures, i.e., bending tests employing concrete prisms with fibre reinforcements. The bond behaviour is compared with the results of the flexural strength of prisms (4 × 4 × 16 cm3) with fibre reinforcements.
The mechanical performance of fibre-reinforced ultra-high-performance concrete based on alkali-activated slag was investigated, concentrating on the use of steel fibres. The flexural strength is slightly higher compared to the UHPC based on Ordinary Portland Cement (OPC) as the binder. Correlating the flexural strength test with multiple fibre-pullout tests, an increase in the bonding behaviour at the interfacial-transition zone of the AAM-UHPC was found compared to the OPC-UHPC. Microstructural investigations on the fibres after storage in an artificial pore solution and a potassium waterglass indicated a dissolution of the metallic surface. This occurred more strongly with the potassium waterglass, which was used as an activator solution in the case of the AAM-UHPC. From this, it can be assumed that the stronger bond results from this initial etching for steel fibres in the AAM-UHPC compared to the OPC-UHPC. The difference in the bond strength of both fibre types, the brass-coated steel fibres and the stainless-steel fibres, was rather low for the AAM-UHPC compared to the OPC-UHPC.
Prestressing of concrete is a commonly used technique in civil engineering to achieve long spans, reduced structural thicknesses, and resource savings. However, in terms of application, complex tensioning devices are necessary, and prestress losses due to shrinkage and creep of the concrete are unfavourable in terms of sustainability. In this work, a prestressing method using novel Fe-Mn-Al-Ni shape memory alloy rebars as a tensioning system in UHPC is investigated. A generated stress of about 130 MPa was measured for the shape memory alloy rebars. For the application in UHPC, the rebars are prestrained prior to the manufacturing process of the concrete samples. After sufficient hardening of the concrete, the specimens are heated inside an oven to activate the shape memory effect and, thus, to introduce the prestress into the surrounding UHPC. It is clearly shown that an improvement in maximum flexural strength and rigidity is achieved due to the thermal activation of the shape memory alloy rebars compared to non-activated rebars. Future research will have to focus on the design of the shape memory alloy rebars in relation to construction applications and the investigation of the long-term performance of the prestressing system.
The influence of reinforcement, especially fibre reinforcement in ultra-high performance concrete is strongly dependent on the bonding (adhesive, shear and friction bond) between metallic surface and cementitious matrix. As usually straight fibres are used for fibre reinforcement and, thus, no significant mechanical bonding is existent, the adhesive bond is particularly important. Previous studies stated that the adhesive bonding behaviour between metallic materials and cementitious matrix strongly depends on the chemical composition of metallic alloys. Therefore, in order to address this topic, the present study investigates the growth of C-S-H phases on stainless steel and on cold drawn steel. This growth process was realised by a surface treatment of the metallic alloys using a synthetically manufactured Tricalciumsilicate (C3S) powder diluted in water. After defined times of the C3S treatment the process is stopped to get a time dependent growing behaviour of the cementitious phases. Light microscopy as well as scanning electron microscopy was used in order to investigate the surfaces following the application of the C3S. The results reveal that the growth of C-S-H phases is more dependent on the metallic surface and its topography than on the alloy composition.