This paper presents the development of a novel one-side-electrode-type fluidic-based capacitive pressure sensor. A pressure sensor using a one-side-electrode and an implementation of electrical double layer capacitance concept was proposed. Mechanical analysis of the membrane was carried out using the finite-element analysis in terms of deflection and Mises stress. A sensor with a circular membrane radius of 3.2 mm, membrane thickness of 0.8 mm, microchannel thickness of 0.5 mm, and microchannel width of 0.5 mm was fabricated using polydimethylsiloxane. The validation was made between the analytical and experimental results for fluid mechanisms inside the sensor. This showed that the displacement for all types of liquid, including methanol, ethanol, and silicon oil was linearly aligned. Methanol was chosen as an electrolyte due to its liquid properties, such as low surface tension and dielectric permittivity. From the experimental results, the operating frequency, response time, and sensitivity of the sensor were 1.2 kHz, 0.12 s, and 0.77 pF/kPa, respectively. The effects of vibration, temperature, and lifetime were also discussed in this paper.
This paper proposed a new teaching technique for engineering courses based on the implementation of drone technology. In some engineering related courses, teaching and learning are difficult due to very complex theoretical and technical explanation need to be digested by the non experienced students. In Malaysia, quadcopter is one of the technologies that become popular among young generation due to its capabilities and interesting features in various application such as aerial photography, aerial monitoring as well as aerial racing tournament. The use of quadcopter thought to be one of the best ways to introduce some engineering concept through a practical exposure followed by project based learning. The concept is able to enhance the understanding as students are exposed to a practical and visual approach used during the learning process. The outcomes shows that once the student gain confidence in building the drone unit, they are ready to explore more on the engineering disciplines through the process. Open source flight software, Mission Planner, is used to configure every components used in the development.
1 April 2023 in International Journal of Electrical and Computer Engineering (IJECE)
Water pollution is one of the most serious environmental problems in Malaysia. The most notable occurrence of pollution happened in Selangor. Currently, there are various water quality monitoring (WQM) methods to observe the quality of water. One of the methods used is the internet of things (IoT) for wireless sensor network technology to obtain real-time data measurement. In this study, the developed WQM system is equipped with a sensor that can measure total dissolved solid (TDS) and electrical conductivity (EC). Arduino UNO was used in this system as a microcontroller to interact with the sensor. The Wi-Fi module, ESP8266, was used to transfer the collected data to ThingSpeak, which acts as a cloud to store all the data. The results showed that both sample populations can be discriminated since the p-value is greater than 0.05 in the normality test, while in the paired sample t-test, the p-value is less than 0.05. In conclusion, this research provides an easier way to monitor water quality by taking up less time at less cost, as well as being reliable in giving real-time data reading.
This paper reported the characterization study on a new type of acoustic microsensor meant for immersion or underwater application. The new proposed device is based on microfluidic technology that is found to be able to overcome the fabrication issues associated with conventional capacitive micromachined ultrasonic transducer device. The design parameters have been explained in detail as well as their design justification. In this paper, two experiments have been setup to characterize the device performance. First, the pulse catch technique was used to investigate the device's response toward acoustic pulse or burst signal. The result shows that different number of burst cycles affects the capacitive response of the device. Providing the acoustic projector with suitable burst cycle parameter had yielded capacitive response with resolution of 1.16 pF, which is useful to be deployed in any suitable application such as for control or communication purposes. Second, the vibration effect had been studied between the ranges of 10-100 Hz of vibration. For rapid transition of the vibration frequency, the fall transition has a comparable error compared with the rise transition with an error ratio of 37:1. In terms of fluctuation behavior of the response, operating the device at static or constant frequency vibration does not have significant differences on the response, indicating its stability at single-frequency operation.
This paper reports the initial investigation on a novel acoustic sensor design based on micro fluidic technology. The report includes the proposed design structure and the simulation of key structure materials that affect the performance of such sensor. Simulation works included the analysis of acoustic response of the membrane and the damping effect when the cavity gap is filled with liquid or electrolyte material. For membrane analysis three different materials, silicon nitride (Si 3 N 4 ), Teflon and Polydimethylsiloxane (PDMS) are simulated to obtain the most responsive material with respect to acoustic pressure signal. PDMS was found to be the most responsive material with the deflection sensitivity of 1.6 μm/Pa. Both Si 3 N 4 and Teflon yielded a sensitivity of 0.034 μm/Pa and 0.67 μm/Pa respectively. In damping analysis, Propylene Carbonate electrolyte was used as a backing layer that filled the cavity gap. With the PDMS was selected as the membrane structure, harmonic analysis was performed to investigate the damping effect caused by electrolyte material on resonance frequency and deflection sensitivity. Result showed that with the proposed design structure and electrolyte backing layer, the harmonic frequency was shifted to a lower value with the maximum deflection was reduced by about 50%. The result also suggests the needs for selecting the right gap material for micro fluidic application that can compromise the damping and the response of the membrane.
This work aims to validate the 2D Finite Element Model (FEM) for estimating the capacitance changes across a microchannel with coplanar electrodes configuration employed. Such electrodes configuration becomes popular in microfluidic-based application where the sensing activity occurs inside a microchannel. ANSYS 12.1 is used to built the 2D model of the structure. The work begin by building the FEM model to find the capacitance per unit length, C/l or C* of different combination of coplanar structures. The variation yields an error of less than 17% as compared to analytical equation with both models having the same trend of capacitance changes. Then, based on the theory of capacitance in parallel, both models are further verified experimentally using a fabricated sensor device that employs a selected structure combination. Comparing the FEM and analytical model to the experimental measurement, the result shows the error of 5% and 24% for both models, respectively.