Surface modification techniques have been developed significantly in the last couple of decades for enhanced tribological performance of artificial hip implants. Surface modification techniques improve biological, chemical and mechanical properties of implant surfaces. Some of the most effective techniques, namely surface texturing, surface coating, and surface grafting, are applied to reduce the friction and wear of artificial implants. This article reviews the status of the developments of surface modification techniques and their effects on commonly used artificial joint implants. This study focused only on artificial hip joint prostheses research of the last 10 years. A total of 27 articles were critically reviewed and categorized according to surface modification technique. The literature reveals that modified surfaces exhibit reduced friction and enhanced wear resistance of the contact surfaces. However, the wear rates are still noticeable in case of surface texturing and surface coating. The associated vortex flow aids to release entrapped wear debris and thus increase the wear particles generation in case of textured surfaces. The earlier delamination of coating materials due to poor adhesion and graphitization transformation has limited the use of coating techniques. Moreover, the produced wear debris has adverse effects on biological fluid. Conversely, the surface grafting technique provides phospholipid like layer that exhibited lower friction and almost zero wear rates even after a longer period of friction and wear test. The findings suggest that further investigations are required to identify the role of surface grafting on film formation and heat resistance ability under physiological hip joint conditions for improved performance and longevity of hip implants.
23 October 2018 in Journal of Thermal Science and Engineering Applications
The dry-low-NOx (DLN) micromix combustion technology has been developed originally as a low emission alternative for industrial gas turbine combustors fueled with hydrogen. Currently, the ongoing research process targets flexible fuel operation with hydrogen and syngas fuel. The nonpremixed combustion process features jet-in-crossflow-mixing of fuel and oxidizer and combustion through multiple miniaturized flames. The miniaturization of the flames leads to a significant reduction of NOx emissions due to the very short residence time of reactants in the flame. The paper presents the results of a numerical and experimental combustor test campaign. It is conducted as part of an integration study for a dual-fuel (H2 and H2/CO 90/10 vol %) micromix (MMX) combustion chamber prototype for application under full scale, pressurized gas turbine conditions in the auxiliary power unit Honeywell Garrett GTCP 36-300. In the presented experimental studies, the integration-optimized dual-fuel MMX combustor geometry is tested at atmospheric pressure over a range of gas turbine operating conditions with hydrogen and syngas fuel. The experimental investigations are supported by numerical combustion and flow simulations. For validation, the results of experimental exhaust gas analyses are applied. Despite the significantly differing fuel characteristics between pure hydrogen and hydrogen-rich syngas, the evaluated dual-fuel MMX prototype shows a significant low NOx performance and high combustion efficiency. The combustor features an increased energy density that benefits manufacturing complexity and costs.
1 November 2018 in Journal of the Mechanical Behavior of Biomedical Materials
Rolling contact fatigue (RCF) is a common failure mode for rolling element bearings, however evidence of precursor failure modes or initiators can be lost or obscured by the subsequent severe damage caused by RCF. Although electric discharge damage (EDD) is not normally associated with rolling element bearings in aviation propulsion applications, it can occur and may not be instantly recognisable. Unlike factors such as lubricant cleanliness or misalignment, EDD does not normally form part of the life prediction of aviation propulsion rolling element bearings. Early identification of EDD and subsequent mitigation or elimination is, therefore, essential to prevent significant reduction in life or failure of rolling element bearings. This paper will review the phenomenon of EDD and discuss several recent examples observed in aviation propulsion systems.
Shape memory alloys (SMAs) are a class of functional materials with the ability to regain their original shapes after a large inelastic deformation upon external stimuli. In recent years, SMAs have been employed in many applications in different fields. Nitinol is the most widely used SMA due to its outstanding properties such as shape memory effect, superelasticity, biocompatibility, and corrosion resistance among other types of SMAs. Some efforts are also made to implement SMAs on filtration devices that require deployable structures. This motivates the authors to write a review of the recent developments in the field of SMA based filtration devices as far as the use of SMAs is concerned. The present work provides a brief overview of history and basics of SMAs. This paper then reviews and discusses the recent progress and applications of SMA based filtration devices and the challenges of these filtration devices. It is found that most devices are made of nitinol. The aim of this paper is to introduce SMA based filtration devices and promote future developments of functional filtration applications.