Sherman Wong

Dr. Sherman Wong


Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 February 2019 in Carbon
Verified
Journal Article
Closed access
SWSherman Wong
Sherman Wong
TST.B. Shiell
T.B. Shiell
BCB.A. Cook
B.A. Cook
JBJ.E. Bradby
J.E. Bradby
DMDavid R McKenzie
David R McKenzie
DMD.G. McCulloch
D.G. McCulloch

9 October 2020 in Journal of Materials Chemistry C
Verified
Journal Article
Closed access
PDF file
JKJaewon Kim
Jaewon Kim
SWSherman Wong
Sherman Wong
GKGahui Kim
Gahui Kim
YPYoung-Bae Park
Young-Bae Park
JEJoel van Embden
Joel van Embden
Enrico Della GasperaEnrico Della Gaspera
Enrico Della Gaspera
Transparent electrodes are key components of optoelectronic devices such as solar cells, light emitting diodes and touchscreen displays. Despite great progress, there remain several challenges to be addressed in transparent conducting coatings, especially for achieving high-performance materials with scalable and inexpensive production. Here we present the deposition of fluorine-doped tin oxide (FTO) thin films with enhanced optoelectronic and mechanical properties using ultrasonic spray pyrolysis. We systematically investigate the influence of deposition temperature and doping amount on the structural, electrical, optical and mechanical properties of FTO films using a suite of characterization techniques including X-ray diffraction, scanning electron microscopy, optical spectroscopy, Hall effect measurement and nanoindentation. We discovered that at a given dopant level, grain size dictates the electrical and mechanical properties, with larger grain sizes and the reduction in grain boundaries – achieved at higher deposition temperatures – promoting an increase in electron mobility and in mechanical strength due to the inverse Hall-Petch effect. The effect of fluorine doping is complementary to that of deposition temperature: the amount of fluorine does not significantly affect grain size and mechanical properties, however it has a great effect on the optical and electrical properties of FTO. Using optimized deposition conditions we achieved FTO coatings with excellent optoelectronic properties (electrical resistivity ∼7 × 10−4 Ω cm; visible transparency ∼90%) and enhanced mechanical properties (elastic modulus ∼170 GPa; hardness ∼16 GPa). These results are some of the best ever reported for FTO films, and provide a solid base for their direct implementation within optoelectronic devices.

1 November 2018 in Journal of the Mechanical Behavior of Biomedical Materials
Verified
Journal Article
Closed access
Subir GhoshSubir Ghosh
Subir Ghosh
Sylvester AbanteribaSylvester Abanteriba
Sylvester Abanteriba
SWSherman Wong
Sherman Wong
SHShadi Houshyar
Shadi Houshyar

24 December 2015 in Journal of Applied Physics
Verified
Journal Article
Closed access
SWSherman Wong
Sherman Wong
BHB. Haberl
B. Haberl
JWJames S. Williams
James S. Williams
JBJ. E. Bradby
J. E. Bradby
The transformation of diamond-cubic silicon to the metallic β-Sn phase is known to be “sluggish,” even when the critical pressure (∼11 GPa) for the transformation is reached. In this letter, we use nanoindentation to apply pressures to just above the critical threshold. In this regime, the sample displays purely elastic behavior at zero hold time. As the hold time at maximum load is increased up to 180 s, the percentage of indents that plastically deform also increase. Interestingly, the indents deform via one of two distinct processes: either via a phase transformation to a mixed bc8/r8-Si end phase, or by initiation of crystalline defects. Raman spectroscopy and cross-sectional transmission electron microscopy are used to show that the two deformation mechanisms are mutually exclusive under the indentation conditions presented here, and elastic modelling was utilized to propose a model for this mutually exclusive behavior. Hence, this behavior enhances the potential for application of the exotic bc8/r8-Si end phase.

9 September 2019 in Journal of Applied Physics
Verified
Journal Article
Open access
PDF file
SWSherman Wong
Sherman Wong
BJB. C. Johnson
B. C. Johnson
BHB. Haberl
B. Haberl
AMAndres Mujica
Andres Mujica
JMJ. C. McCallum
J. C. McCallum
JBJ. E. Bradby
J. E. Bradby
Novel phases of Si that are predicted to have industrially desirable properties can be recovered after indentation-induced pressure. However, the thermal stability of these phases is not well understood. Furthermore, in the past, different methods of annealing have resulted in conflicting reports on annealing stability and transformation pathways. This study investigates the thermal stability of several metastable Si phases called r8-Si, bc8-Si, hd-Si, and Si-XIII under furnace annealing, incremental annealing, and laser annealing using Raman microspectroscopy and electron diffraction. The temperature range of stability for these metastable phases is thus determined. Of particular interest, hd-Si is stable to a much higher temperature than previously reported, being the predominant phase observed in this study after annealing at 450 °C. This finding was enabled through a new method for confirming the presence of hd-Si by detailed electron diffraction. This high thermal stability generates renewed interest in exploiting this phase for industrial applications, such as strain-tailored solar absorption.

22 June 2015 in Applied Physics Letters
Verified
Journal Article
Closed access
PDF file
SWSherman Wong
Sherman Wong
BHB. Haberl
B. Haberl
JWJames S. Williams
James S. Williams
JBJ. E. Bradby
J. E. Bradby
The metastable body-centered cubic (bc8) and rhombohedral (r8) phases of silicon that are formed after the nanoindentation of diamond cubic silicon exhibit properties that are of both scientific and technological interest. This letter demonstrates that large regions of these phases can be readily formed from crystalline silicon via nanoindentation with minimal damage to the surrounding crystal. Cross-sectional transmission electron microscopy is used to show that volumes of these phases 6 μm wide and up to 650 nm deep can be generated using a symmetrical spherical tip of ∼21.5 μm diameter. This result indicates that the use of large symmetrical spherical tips result in highly hydrostatic conditions that can favor the single phase transformation mode without extensive damage to the surrounding crystalline regions that are observed in previous studies.