The wide magnesium (Mg) alloy sheets produced by twin-roll casting (TRC) are prone to have an inhomogeneous microstructure and basal texture. Texture has a significant effect on the properties of Mg alloy sheets for the processes after TRC, which can be greatly modified by alloy composition. However, systematic studies on the bulk texture of TRCed Mg alloy sheets using neutron diffraction are lacking. In this study, neutron diffraction was used to explore the bulk textures in different positions of the Mg, Mg–Al–Zn, and Mg–Al–Sn–Zn alloy sheets produced by TRC, besides microstructure and micro-texture analysis using field emission scanning electron microscopy and electron backscattering diffraction. The influence of alloy composition on the microstructure and texture evolution of TRCed Mg alloy sheets is explored and discussed. The TRCed pure Mg sheet possesses a relatively strong basal texture, and the texture distribution is inhomogeneous; while TRCed Mg–Al–Sn–Zn alloy sheets feature much weaker textures and a relatively homogenous distribution in different positions. The present study provides guidance for the control of texture via tailoring alloy compositions, which provides candidate Mg alloys suitable for the TRC process.

The first neutron texture diffractometer in China has been built at the China Advanced Research Reactor, due to strong demand for texture measurement with neutrons from the domestic user community. This neutron texture diffractometer has high neutron intensity, moderate resolution and is mainly applied to study texture in commonly used industrial materials and engineering components. In this paper, the design and characteristics of this instrument are described. The results for calibration with neutrons and quantitative texture analysis of zirconium alloy plate are presented. The comparison of texture measurements with the results obtained in HIPPO at LANSCE and Kowari at ANSTO illustrates the reliability of the texture diffractometer.

The wide Mg alloy sheets produced by hot extrusion usually can easily form an inhomogeneous texture, resulting in anisotropic mechanical properties and poor formability. However, few studies have been carried out on the bulk texture investigation at different areas of as-extruded Mg alloy sheets, especially the Mg alloys with different alloying elements. In this work, the effect of Al on the bulk texture and mechanical properties at different areas for three wide Mg-Al-Zn alloy sheets with different Al contents (Mg-3Al-0.5Zn, Mg-8Al-0.5Zn and Mg-9Al-0.5Zn) are mainly investigated by neutron diffraction. The results showed that a strong and uneven basal texture was formed in the Mg-3Al-0.5Zn sheet. Meanwhile, the intensity of the basal texture was significantly weakened due to the numerous fine precipitates of Mg₁₇Al₁₂ particles, with the Al content increasing, which hinder the grain growth during extrusion, while fine recrystallized grains have a more random orientation. The enhanced tensile properties in Mg-8Al-0.5Zn and Mg-9Al-0.5Zn alloy sheets are ascribed to the cooperation effect of a refined microstructure, precipitates and weakened basal texture. Among the three Mg alloy sheets, the Mg-8Al-0.5Zn alloy sheet has a yield strength of about 270 MPa, an ultimate tensile strength of about 330 MPa and ultimate elongation of about 16% in the extrusion direction, which possesses the most excellent comprehensive mechanical properties.

17-4PH martensitic steel is usually used as valve stems in nuclear power plants and it suffers from thermal aging embrittlement due to long-time service in a high-temperature and high-pressure environment. Here, we characterized the evolution of microstructures at the nano-scale in 17-4PH steel by in situ small-angle neutron scattering (SANS) with a thermo-mechanically coupled loading device. The device could set different temperatures and tensile so that an in situ SANS experiment could dynamically characterize the process of nanoscale structural changes. The results showed that with increasing thermal aging time, the ε-Cu phase precipitates and grows as the temperature is 475 °C and 590 °C, and the ε-Cu phase is spherical at 475 °C but became elongated cylinders at 590 °C. Moreover, the loading stress could aid in the growth of the ε-Cu phase at 475 °C.