Kamran Nikbin

Dr. Kamran Nikbin

Mechanical Engineering Department, Imperial College, London SW7 2AZ, UK

Research Focus & Metrics

Academic Career Length

21Years (2006-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 October 2021 in Materials
Verified
Journal Article
Open access
PDF file
JXJiangjing Xi
Jiangjing Xi
YHYun Hu
Yun Hu
XHXing Hui
Xing Hui
Yuanfei HanYuanfei Han
Yuanfei Han
HZHaiying Zhang
Haiying Zhang
Kamran NikbinKamran Nikbin
Kamran Nikbin
Selective laser melting (SLM) is a promising additive manufacturing (AM) process for high-strength or high-manufacturing-cost metals such as Ti-6Al-4V widely applied in aeronautical industry components with high material waste or complex geometry. However, one of the main challenges of AM parts is the variability in fatigue properties. In this study, standard cyclic fatigue and monotonic tensile testing specimens were fabricated by SLM and subsequently heat treated using the standard heat treatment (HT) or hot isostatic pressing (HIP) methods. All the specimens were post-treated to relieve the residual stress and subsequently machined to the same surface finishing. These specimens were tested in the low-cycle fatigue (LCF) regime. The effects of post-process methods on the failure mechanisms were observed using scanning electron microscopy (SEM) and optical microscopy (OM) characterization methods. While the tensile test results showed that specimens with different post-process treatment methods have similar tensile strength, the LCF test revealed that no significant difference exists between HT and HIP specimens. Based on the results, critical factors influencing the LCF properties are discussed. Furthermore, a microstructure-based multistage fatigue model was employed to predict the LCF life. The results show good agreement with the experiment.


1 March 2014 in Computational Materials Science
Verified
Journal Article
Closed access
FBFarid Reza Biglari
Farid Reza Biglari
Kamran NikbinKamran Nikbin
Kamran Nikbin

4 August 2022 in Journal of Materials Science & Technology
Verified
Journal Article
Closed access
KZKun Zhang
Kun Zhang
JTJian-Ping Tan
Jian-Ping Tan
WSWei Sun
Wei Sun
Kamran NikbinKamran Nikbin
Kamran Nikbin
STShan-Tung Tu
Shan-Tung Tu

1 July 2011 in International Journal of Mechanical Sciences
Verified
Journal Article
Closed access
SHSeok-Pyo Hong
Seok-Pyo Hong
JAJoong-Hyok An
Joong-Hyok An
YKYun-Jae Kim
Yun-Jae Kim
Kamran NikbinKamran Nikbin
Kamran Nikbin
PBPeter J. Budden
Peter J. Budden

29 April 2009 in Journal of Pressure Vessel Technology
Verified
Journal Article
Closed access
PDF file
TTTomasz Tkaczyk
Tomasz Tkaczyk
NONoel O'Dowd
Noel O'Dowd
Kamran NikbinKamran Nikbin
Kamran Nikbin
An accurate defect assessment procedure is needed to ensure integrity of girth welded steel pipelines while avoiding unnecessary repairs. An integral part of such a procedure is an estimation scheme for the crack driving force. In this work, a modified reference stress solution was developed for the assessment of elastic-plastic pipes with surface breaking defects. For the particular case of interest (reeled offshore pipelines), the loading is phrased in terms of applied strain. The stress-based approach has therefore been extended to the case of strain/displacement control. The results obtained using the modified reference stress solution have been compared with a three-dimensional finite-element analysis. Very good agreement has been obtained. The predictions are also significantly better than those obtained from existing approaches. A comparison between the proposed method and full scale testing will be presented in a separate paper.