Eckhard Mueller

Eckhard Mueller


Research Focus & Metrics

Academic Career Length

25Years (2002-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
15 August 2011 in Entropy
Verified
Journal Article
Open access
PDF file
CGChristophe Goupil
Christophe Goupil
WSWolfgang Seifert
Wolfgang Seifert
KZKnud Zabrocki
Knud Zabrocki
EMEckhard Mueller
Eckhard Mueller
GSG. Jeffrey Snyder
G. Jeffrey Snyder
Fifty years ago, the optimization of thermoelectric devices was analyzed by considering the relation between optimal performances and local entropy production. Entropy is produced by the irreversible processes in thermoelectric devices. If these processes could be eliminated, entropy production would be reduced to zero, and the limiting Carnot efficiency or coefficient of performance would be obtained. In the present review, we start with some fundamental thermodynamic considerations relevant for thermoelectrics. Based on a historical overview, we reconsider the interrelation between optimal performances and local entropy production by using the compatibility approach together with the thermodynamic arguments. Using the relative current density and the thermoelectric potential, we show that minimum entropy production can be obtained when the thermoelectric potential is a specific, optimal value.

25 October 2002 in Physica Status Solidi (a)
Verified
Journal Article
Closed access
PDF file
WSW. Seifert
W. Seifert
MUM. Ueltzen
M. Ueltzen
EMEckhard Mueller
Eckhard Mueller

3 May 2006 in Physica Status Solidi (a)
Verified
Journal Article
Closed access
PDF file
EMEckhard Mueller
Eckhard Mueller
SWSteven Walczak
Steven Walczak
WSWolfgang Seifert
Wolfgang Seifert

6 April 2010 in Journal of Electronic Materials
Verified
Journal Article
Closed access
PDF file
KZK. Zabrocki
K. Zabrocki
EMEckhard Mueller
Eckhard Mueller
WSW. Seifert
W. Seifert

16 December 2018 in Applied Sciences
Verified
Journal Article
Open access
PDF file
PZPaweł Ziolkowski
Paweł Ziolkowski
KZKnud Zabrocki
Knud Zabrocki
EMEckhard Mueller
Eckhard Mueller
Finite element model (FEM)-based simulations are conducted for the application of a thermoelectric generator (TEG) between the hot core stream and the cool bypass flow at the nozzle of an aviation turbofan engine. This work reports the resulting requirements on the TEG design with respect to applied thermoelectric (TE) element lengths and filling factors (F) of the TE modules in order to achieve a positive effect on the specific fuel consumption. Assuming a virtual optimized TE material and varying the convective heat transfer coefficients (HTC) between the nozzle surfaces and the gas flows, this work reports the achievable power output. System-level requirement on the gravimetric power density (>100 Wkg−1) can only be met for F ≤ 21%. When extrapolating TEG coverage to the full nozzle surface, the power output reaches 1.65 kW per engine. The assessment of further potential for power generation is demonstrated by a parametric study on F, convective HTC, and materials performance. This study confirms a feasible design range for TEG installation on the aircraft nozzle with a positive impact on the fuel consumption. This application translates into a reduction of operational costs, allowing for an economically efficient TEG-installation with respect to the cost-specific power output of modern thermoelectric materials.

22 February 2022 in Materials
Verified
Journal Article
Open access
PDF file
PZPaweł Ziolkowski
Paweł Ziolkowski
PBPrzemyslaw Blaschkewitz
Przemyslaw Blaschkewitz
BRByungki RYU
Byungki RYU
SPSuDong Park
SuDong Park
EMEckhard Mueller
Eckhard Mueller
The status of metrology for the characterization of thermoelectric generator modules (TEM) is investigated in this work by an international round robin (RR) test including twelve laboratories from nine countries on three continents. Measurements have been performed with three samples of a Bi2Te3-based commercial TEM type, which has prevailed over three competing types during previous tests on the short- and long-term stability. A comparison of temperature-dependent results is provided up to 200 °C hot side temperature for the maximum power output Pmax, the incident heat flow Q˙In (at maximum efficiency conditions), and the maximum efficiency ηmax. Data evaluation from all RR participants reveals maximum standard deviations for these measurands of 27.2% (Pmax), 59.2% (Q˙In), and 25.9% (ηmax). A comparison between RR data sets and reference data from manufacturer specifications shows high deviations of up to 46%, too. These deviations reflect the absence of measurement guidelines and reference samples and confirm the need for improvements in the standardization of TEM metrology. Accordingly, the results of the RR are presented against the background of our own investigations on the uncertainty budgets for the determination of the abovementioned TEM properties using inhouse-developed characterization facilities, which comprise reference and absolute measurement techniques for the determination of heat flow.