SuDong Park

Dr. SuDong Park

orcid

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 March 2016 in Electronic Materials Letters
Verified
Journal Article
Closed access
PDF file
HKHyun Kim
Hyun Kim
JLJae Ki Lee
Jae Ki Lee
SPSuDong Park
SuDong Park
BRByungki RYU
Byungki RYU
JLJi Eun Lee
Ji Eun Lee
YCYoung-Rae Cho
Young-Rae Cho

6 May 2018 in Applied Sciences
Verified
Journal Article
Open access
PDF file
JLJae Ki Lee
Jae Ki Lee
JSJi Hui Son
Ji Hui Son
YKYONG IL KIM
YONG IL KIM
BRByungki RYU
Byungki RYU
BCByung Jin Cho
Byung Jin Cho
Min-Wook OhMin-Wook Oh
Min-Wook Oh
Many elements have been used as dopants to enhance the thermoelectric performance of Bi2Te3-related materials. Among them, Ag’s effect on thermoelectric properties, where Ag acts as a donor or acceptor, remains unclear. To elucidate the role of Ag in n-type Bi2Te3 based compounds, Ag was added to n-type (Bi0.9Sb0.1)2(Te0.85Se0.15)3. As the amount of Ag was increased, the electron concentration decreased, which means Ag acted as an acceptor. The added Ag atoms were found to occupy interstitial sites in the hexagonal lattices, as confirmed by X-ray analysis and first principles calculations. The reduction in electron concentration was attributed to the interaction between the interstitial Ag and intrinsic defects.

22 February 2022 in Materials
Verified
Journal Article
Open access
PDF file
PZPaweł Ziolkowski
Paweł Ziolkowski
PBPrzemyslaw Blaschkewitz
Przemyslaw Blaschkewitz
BRByungki RYU
Byungki RYU
SPSuDong Park
SuDong Park
EMEckhard Mueller
Eckhard Mueller
The status of metrology for the characterization of thermoelectric generator modules (TEM) is investigated in this work by an international round robin (RR) test including twelve laboratories from nine countries on three continents. Measurements have been performed with three samples of a Bi2Te3-based commercial TEM type, which has prevailed over three competing types during previous tests on the short- and long-term stability. A comparison of temperature-dependent results is provided up to 200 °C hot side temperature for the maximum power output Pmax, the incident heat flow Q˙In (at maximum efficiency conditions), and the maximum efficiency ηmax. Data evaluation from all RR participants reveals maximum standard deviations for these measurands of 27.2% (Pmax), 59.2% (Q˙In), and 25.9% (ηmax). A comparison between RR data sets and reference data from manufacturer specifications shows high deviations of up to 46%, too. These deviations reflect the absence of measurement guidelines and reference samples and confirm the need for improvements in the standardization of TEM metrology. Accordingly, the results of the RR are presented against the background of our own investigations on the uncertainty budgets for the determination of the abovementioned TEM properties using inhouse-developed characterization facilities, which comprise reference and absolute measurement techniques for the determination of heat flow.

10 November 2021 in Materials
Verified
Journal Article
Open access
PDF file
JCJulia Camut
Julia Camut
SASahar Ayachi
Sahar Ayachi
GCGustavo Castillo-Hernández
Gustavo Castillo-Hernández
SPSungjin Park
Sungjin Park
BRByungki RYU
Byungki RYU
JBJohannes De Boor
Johannes De Boor
Thermoelectric generators are a reliable and environmentally friendly source of electrical energy. A crucial step for their development is the maximization of their efficiency. The efficiency of a TEG is inversely related to its electrical contact resistance, which it is therefore essential to minimize. In this paper, we investigate the contacting of an Al electrode on Mg2(Si,Sn) thermoelectric material and find that samples can show highly asymmetric electrical contact resistivities on both sides of a leg (e.g., 10 µΩ·cm2 and 200 µΩ·cm2). Differential contacting experiments allow one to identify the oxide layer on the Al foil as well as the dicing of the pellets into legs are identified as the main origins of this behavior. In order to avoid any oxidation of the foil, a thin layer of Zn is sputtered after etching the Al surface; this method proves itself effective in keeping the contact resistivities of both interfaces equally low (<10 µΩ·cm2) after dicing. A slight gradient is observed in the n-type leg’s Seebeck coefficient after the contacting with the Zn-coated electrode and the role of Zn in this change is confirmed by comparing the experimental results to hybrid-density functional calculations of Zn point defects.

15 December 2012 in Electronic Materials Letters
Verified
Journal Article
Closed access
PDF file
JLJ. K. Lee
J. K. Lee
Min-Wook OhMin-Wook Oh
Min-Wook Oh
SPSuDong Park
SuDong Park
BKB. S. Kim
B. S. Kim
BMB. K. Min
B. K. Min
HLH. W. Lee
H. W. Lee

9 February 2022 in Materials
Verified
Journal Article
Open access
PDF file
SPSungjin Park
Sungjin Park
BRByungki RYU
Byungki RYU
SPSuDong Park
SuDong Park
Previous calculations have demonstrated that Te vacancies are energetically the major defects in PbTe. However, the Pb interstitials are also important because experiments have shown that the volume of Pb-rich PbTe increases at a higher Pb content. In this study, density functional theory calculations were used to investigate the defect properties of low-symmetry Pb interstitials in PbTe. By breaking the higher symmetry imposed on the on-centered interstitial defects, the lowest ground state of Pb interstitial defects is off-centered along the [1¯1¯1¯] direction. Because of the four multi-stable structures with low defect-formation energies, the defect density of Pb interstitials is expected to be approximately six times higher than previous predictions for PbTe synthesized at 900 K. In contrast to the on-centered Pb interstitials, the off-centered Pb interstitials in PbTe can exhibit long-range lattice relaxation in the [111] direction beyond a distance of 1 nm, indicating the potential formation of weak local dipoles. This result provides an alternative explanation for the emphanitic anharmonicity of PbTe in the high-temperature regime.