Zachary Alcorn

Dr. Zachary Alcorn


Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
25 September 2020 in Nanomaterials
Verified
Journal Article
Open access
PDF file
ZAZachary Alcorn
Zachary Alcorn
TFTore Føyen
Tore Føyen
JGJarand Gauteplass
Jarand Gauteplass
BBBenyamine Benali
Benyamine Benali
ASAleksandra Sæle
Aleksandra Sæle
MFMartin Fernø
Martin Fernø
Nanoparticles have gained attention for increasing the stability of surfactant-based foams during CO2 foam-enhanced oil recovery (EOR) and CO2 storage. However, the behavior and displacement mechanisms of hybrid nanoparticle–surfactant foam formulations at reservoir conditions are not well understood. This work presents a pore- to core-scale characterization of hybrid nanoparticle–surfactant foaming solutions for CO2 EOR and the associated CO2 storage. The primary objective was to identify the dominant foam generation mechanisms and determine the role of nanoparticles for stabilizing CO2 foam and reducing CO2 mobility. In addition, we shed light on the influence of oil on foam generation and stability. We present pore- and core-scale experimental results, in the absence and presence of oil, comparing the hybrid foaming solution to foam stabilized by only surfactants or nanoparticles. Snap-off was identified as the primary foam generation mechanism in high-pressure micromodels with secondary foam generation by leave behind. During continuous CO2 injection, gas channels developed through the foam and the texture coarsened. In the absence of oil, including nanoparticles in the surfactant-laden foaming solutions did not result in a more stable foam or clearly affect the apparent viscosity of the foam. Foaming solutions containing only nanoparticles generated little to no foam, highlighting the dominance of surfactant as the main foam generator. In addition, foam generation and strength were not sensitive to nanoparticle concentration when used together with the selected surfactant. In experiments with oil at miscible conditions, foam was readily generated using all the tested foaming solutions. Core-scale foam-apparent viscosities with oil were nearly three times as high as experiments without oil present due to the development of stable oil/water emulsions and their combined effect with foam for reducing CO2 mobility

5 February 2020 in E3S Web of Conferences
Verified
Conference Paper
Open access
PDF file
ZAZachary Alcorn
Zachary Alcorn
SFSunniva B. Fredriksen
Sunniva B. Fredriksen
MSMohan Sharma
Mohan Sharma
TFTore Føyen
Tore Føyen
CWConnie Wergeland
Connie Wergeland
GEGeir Ersland
Geir Ersland
This paper presents experimental and numerical sensitivity studies to assist injection strategy design for an ongoing CO2 foam field pilot. The aim is to increase the success of in-situ CO2 foam generation and propagation into the reservoir for CO2 mobility control, enhanced oil recovery (EOR) and CO2 storage. Un-steady state in-situ CO2 foam behavior, representative of the near wellbore region, and steady-state foam behavior was evaluated. Multi-cycle surfactant-alternating gas (SAG) provided the highest apparent viscosity foam of 120.2 cP, compared to co-injection (56.0 cP) and single-cycle SAG (18.2 cP) in 100% brine saturated porous media. CO2 foam EOR corefloods at first-contact miscible (FCM) conditions showed that multi-cycle SAG generated the highest apparent foam viscosity in the presence of refined oil (n-Decane). Multi-cycle SAG demonstrated high viscous displacement forces critical in field implementation where gravity effects and reservoir heterogeneities dominate. At multiple-contact miscible (MCM) conditions, no foam was generated with either injection strategy as a result of wettability alteration and foam destabilization in presence of crude oil. In both FCM and MCM corefloods, incremental oil recoveries were on average 30.6% OOIP regardless of injection strategy for CO2 foam and base cases (i.e. no surfactant). CO2 diffusion and miscibility dominated oil recovery at the core-scale resulting in high microscopic CO2 displacement. CO2 storage potential was 9.0% greater for multi-cycle SAGs compared to co-injections at MCM. A validated core-scale simulation model was used for a sensitivity analysis of grid resolution and foam quality. The model was robust in representing the observed foam behavior and will be extended to use in field scale simulations.

7 September 2022 in Energies
Verified
Journal Article
Open access
PDF file
ZAZachary Alcorn
Zachary Alcorn
ASAleksandra Sæle
Aleksandra Sæle
MKMetin Karakas
Metin Karakas
AGArne Graue
Arne Graue
This work presents a multiscale experimental and numerical investigation of CO2 foam generation, strength, and propagation during alternating injection of surfactant solution and CO2 at reservoir conditions. Evaluations were conducted at the core-scale and with a field-scale radial simulation model representing a CO2 foam field pilot injection well. The objective of the experimental work was to evaluate foam generation, strength, and propagation during unsteady-state surfactant-alternating-gas (SAG) injection. The SAG injection rapidly generated foam based upon the increased apparent viscosity compared to an identical water-alternating-gas (WAG) injection, without surfactant. The apparent foam viscosity of the SAG continually increased with each subsequent cycle, indicating continued foam generation and propagation into the core. The maximum apparent viscosity of the SAG was 146 cP, whereas the maximum apparent viscosity of the WAG was 2.4 cP. The laboratory methodology captured transient CO2 foam flow which sheds light on field-scale CO2 foam flow. The single-injection well radial reservoir simulation model investigated foam generation, strength, and propagation during a recently completed field pilot. The objective was to tune the model to match the observed bottom hole pressure data from the foam pilot and evaluate foam propagation distance. A reasonable match was achieved by reducing the reference mobility reduction factor parameter of the foam model. This suggested that the foam generated during the pilot was not as strong as observed in the laboratory, but it has propagated approximately 400 ft from the injection well, more than halfway to the nearest producer, at the end of pilot injection.

21 April 2022 in Energies
Verified
Journal Article
Open access
PDF file
MKMetin Karakas
Metin Karakas
ZAZachary Alcorn
Zachary Alcorn
Fred AminzadehFred Aminzadeh
Fred Aminzadeh
AGArne Graue
Arne Graue
This study focuses on the use of pressure measurements to monitor the effectiveness of foam as a CO2 mobility control agent in oil-producing reservoirs. When it is applied optimally, foam has excellent potential to improve reservoir sweep efficiency, as well as CO2 utilization and storage, during CO2 Enhanced Oil Recovery (EOR) processes. In this study, we present part of an integrated and novel workflow involving laboratory measurements, reservoir modeling and monitoring. Using the recorded bottom-hole pressure data from a CO2 foam pilot study, we demonstrate how transient pressures could be used to monitor CO2 foam development inside the reservoir. Results from a recent CO2 foam pilot study in a heterogeneous carbonate field in Permian Basin, USA, are presented. The injection pressure was used to evaluate the development of foam during various foam injection cycles. A high-resolution radial simulator was utilized to study the effect of foam on well injectivity, as well as on CO2 mobility in the reservoir during the surfactant-alternating gas (SAG) process. Transient analysis indicated constant temperature behavior during all SAG cycles. On the other hand, differential pressures consistently increased during the surfactant injection and decreased during the subsequent CO2 injection periods. Pressure buildup during the periods of surfactant injection indicated the development of a reduced mobility zone in the reservoir. The radial model proved to be useful to assess the reservoir foam strength during this pilot study. Transient analysis revealed that the differential pressures during the SAG cycles were higher than the pressures observed during the water-alternating gas (WAG) cycle which, in turn, showed foam generation and reduced CO2 mobility in the reservoir. Although pressure data are a powerful indicator of foam strength, additional measurements may be required to describe the complex physics of in situ foam generation. In this pilot study, it appeared that the reservoir foam strength was weaker than that expected in the laboratory.

27 November 2025 in Energies
Verified
Journal Article
Open access
PDF file
HHHilde Halsøy
Hilde Halsøy
AGArne Graue
Arne Graue
ZAZachary Alcorn
Zachary Alcorn
Foam is a field-proven technique to reduce CO2 mobility and mitigate the impacts of reservoir heterogeneity in CO2-enhanced oil recovery (CO2-EOR). However, foams are unstable and tend to break down in the presence of oil. Screening foam generation and stability in the presence of oil, at representative reservoir pressure and temperature, at core-scale is critical for successful upscaling. This study investigates the effect of oil on foam generation and stability across a range of foam qualities (fg = 0.30 to 1.0) and injection velocities (4 ft/day to 16 ft/day). Foam quality and rate scans using Bentheimer sandstone cores were conducted in presence/absence of oil (n-decane and Troll crude) at reservoir conditions (60 °C and 180 bar). Foam quality scans co-injected supercritical CO2 and foaming solutions with increasing foam quality (fg = 0.30 to 1.0) to determine the optimal foam quality (highest apparent viscosity foam). T optimal foam quality was then used in rate scans to determine the effect of injection velocity on foam strength. In addition, two separate core floods at two fixed foam qualities (fg = 0.30 and 0.70) were performed to determine the oil recovery factor during foam injection. Strong foam was generated, in both the presence and absence of oil, but oil significantly reduced foam strength. The foam apparent viscosity was reduced by ~93% (Troll crude) and ~90% (n-decane) compared to foam in the absence of oil. Increasing the surfactant concentration from 0.10 wt.% to 1.0 wt.% significantly enhanced the foam mobility control, with the apparent viscosity in the presence of oil increasing from 7.9 cP to 25.9 cP. The optimal foam quality in the presence of both oils ranged from fg = 0.60 to 0.70. Foam rate scans revealed shear-thinning rheology (foam viscosity decreased at higher flow rates), which is beneficial for maintaining field-scale injectivity. This study provides critical insights into how oil impacts supercritical CO2 foam strength, stability mechanisms, and oil recovery at reservoir conditions, crucial for field-scale implementation in CO2-EOR and CO2 storage projects.

1 October 2026 in Petroleum
Verified
Journal Article
Open access
JLJorge Rodrigo Lligüizaca-Dávila
Jorge Rodrigo Lligüizaca-Dávila
FCFreddy Paul Carrión-Maldonado
Freddy Paul Carrión-Maldonado
DLDavid Landa-Marbán
David Landa-Marbán
JSJorge Segundo Mendoza Sanz
Jorge Segundo Mendoza Sanz
ZAZachary Alcorn
Zachary Alcorn
JCJacquelin E. Cobos
Jacquelin E. Cobos