Arne Graue

Prof. Dr. Arne Graue

orcid

Research Focus & Metrics

Academic Career Length

33Years (1994-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 March 1994 in SPE Drilling & Completion
Verified
Journal Article
Closed access
PDF file
AGArne Graue
Arne Graue
Systematic experimental studies of the effect from capillary heterogeneities and permeability variations on the development of total saturation distributions during oil-drainage and waterfloods in long sandpack columns have been conducted. A nuclear imaging technique has been used to obtain one dimension at dynamic in situ saturation profiles during the displacements. Well-defined capillary profiles during the displacements. Well-defined capillary heterogeneities are obtained by pecking a sandcolumn with alternating sand Layers of different permeability in series. in the direction of displacement. During the displacement of the wetting phase, capillary effects cause wetting phase accumulation at the transition zone from the porous media featuring high capillarity to the Lower capillarity sand. During displacement of the non-wetting phase, the higher capillarity sand exhibits higher sweep phase, the higher capillarity sand exhibits higher sweep efficiency and Lower residual saturation of the nonwetting phase than the Lower capillarity sand. This displacement behavior creates step-Like saturation profiles corresponding to the permeability variations. profiles corresponding to the permeability variations. Systematic single parameter variations of the mobility, the flow-rate and the wetting situation for the displaced fluid were performed, end the repeatability was tested. The saturation response is found to be higher for Lower flow-rates, for more unfavorable mobility situations and is most predominant in the displacement process of the non-wetting phase. Applications of the results can be useful in interpretations of coreflood displacements with respect to heterogeneities and in the prediction of parameters such as local residual saturations, saturation parameters such as local residual saturations, saturation front velocities and relative permeabilities in heterogeneous media. Introduction Petroleum recovery from reservoir rocks faces the problems Petroleum recovery from reservoir rocks faces the problems associated to the physics of multiphase flow in porous media. Research on two- and three phase flow in reservoir rocks has over the years also fully demonstrated the complex and interdependent interactions between geological. chemical and physical parameters, severly affecting the ultimate recovery. Experimental studies of flow behavior representative for a given formation, are Limited to minute fractions of the reservoir, i.e. samples taken from wellbore cores. However, the rock characteristics usually vary spatially quite considerably. This fact has often been neglected or by different means statistically been conveniently averaged. However, several important parameters are known to have tensor characteristics and quite parameters are known to have tensor characteristics and quite often need a more precise and deterministic treatment. Concern about this spatial variation of fluid/rock properties has recently lead to a growing interest to properties has recently lead to a growing interest to understand how different types of heterogenieties influence the displacement processes. This interest is partly due to the fact that modern technology now offers partly due to the fact that modern technology now offers possibilities through improved computational means, to possibilities through improved computational means, to model and calculate Large-scale effects from reservoir heterogeneities (1). But in order to understand the impacts from different kinds of heterogeneities, at the different scales, laboratory studies are essential. In spite of careful selections of core material for laboratory core floods, it is well known that heterogeneities within core plugs can disturb and influence the fluid flow. Due to technological advances in characterization of natural rocks and in probing and monitoring techniques these phenomena are by now possible to approach. By applying visualization techniques laboratory core floods offer sore reliable and reproducible results, as the experiments give information on the local saturation development. The objective is to understand and explain how heterogeneities impact on recovery efficiency and on physical parameters as e.g. relative permeability and physical parameters as e.g. relative permeability and capillary pressure.

1 July 2021 in Journal of Petroleum Science and Engineering
Verified
Journal Article
Closed access
JCJacquelin E. Cobos
Jacquelin E. Cobos
MSMartine Sandnes
Martine Sandnes
MSMarianne Steinsbø
Marianne Steinsbø
BBBergit Brattekås
Bergit Brattekås
ESErik G. Søgaard
Erik G. Søgaard
AGArne Graue
Arne Graue

16 April 2013
Verified
Conference Paper
Closed access
PDF file
JGJarand Gauteplass
Jarand Gauteplass
HFH.N. Follesø
H.N. Follesø
AGArne Graue
Arne Graue
AKAnthony Kovscek
Anthony Kovscek
MFM.A. Fernø
M.A. Fernø

13 April 2015
Verified
Conference Paper
Closed access
PDF file
BBBergit Brattekås
Bergit Brattekås
AGArne Graue
Arne Graue
RSRandall Seright
Randall Seright
Polymer gels are frequently applied for conformance improvement in fractured reservoirs, where fluid channeling through fractures limits the success of waterflooding. Placement of polymer gel in fractures reduces fracture conductivity, thus increasing pressure gradients across matrix blocks during chase floods. A gel-filled fracture is re-opened to fluid flow if the injection pressure during chase floods exceeds the gel rupture pressure, thus channeling through the fractures resumes. The success of a polymer gel treatment therefore depends on the rupture pressure. Swelling of gels, e.g. pre-formed particle gels, due to salinity differences between the gel network and surrounding water phase has recently been observed, but the effect has been less studied in conjunction with conventional polymer gels. Using core floods, this study demonstrates that low-salinity water can swell conventional Cr(III)-acetate HPAM gels, thereby improving gel blocking performance after gel rupture. Formed polymer gel was placed in fractured core plugs and chase waterfloods were performed, using four different brine compositions of which three were low-salinity brines. The fluid flow rates through the matrix and differential pressures across the matrix and fracture were measured and shown to increase with decreasing salinity in the injected water phase. In some cores, the fractures were re-blocked during low-salinity waterfloods, and gel blocking capacity was increased above the initial level. Low-salinity water subsequently flooded the matrix during chase floods, which provided additional benefits to the waterflood. The improved blocking capacity of the gel was caused by a difference in salinity between the gel and injected water phase, which induced gel swelling. The results were reproducible through several experiments, and stable for long periods of time in both sandstone and carbonate outcrop core materials. Combining polymer gel placement in fractures with low-salinity chase floods is a promising approach in integrated EOR (IEOR).

7 September 2022 in Energies
Verified
Journal Article
Open access
PDF file
ZAZachary Alcorn
Zachary Alcorn
ASAleksandra Sæle
Aleksandra Sæle
MKMetin Karakas
Metin Karakas
AGArne Graue
Arne Graue
This work presents a multiscale experimental and numerical investigation of CO2 foam generation, strength, and propagation during alternating injection of surfactant solution and CO2 at reservoir conditions. Evaluations were conducted at the core-scale and with a field-scale radial simulation model representing a CO2 foam field pilot injection well. The objective of the experimental work was to evaluate foam generation, strength, and propagation during unsteady-state surfactant-alternating-gas (SAG) injection. The SAG injection rapidly generated foam based upon the increased apparent viscosity compared to an identical water-alternating-gas (WAG) injection, without surfactant. The apparent foam viscosity of the SAG continually increased with each subsequent cycle, indicating continued foam generation and propagation into the core. The maximum apparent viscosity of the SAG was 146 cP, whereas the maximum apparent viscosity of the WAG was 2.4 cP. The laboratory methodology captured transient CO2 foam flow which sheds light on field-scale CO2 foam flow. The single-injection well radial reservoir simulation model investigated foam generation, strength, and propagation during a recently completed field pilot. The objective was to tune the model to match the observed bottom hole pressure data from the foam pilot and evaluate foam propagation distance. A reasonable match was achieved by reducing the reference mobility reduction factor parameter of the foam model. This suggested that the foam generated during the pilot was not as strong as observed in the laboratory, but it has propagated approximately 400 ft from the injection well, more than halfway to the nearest producer, at the end of pilot injection.

21 April 2022 in Energies
Verified
Journal Article
Open access
PDF file
MKMetin Karakas
Metin Karakas
ZAZachary Alcorn
Zachary Alcorn
Fred AminzadehFred Aminzadeh
Fred Aminzadeh
AGArne Graue
Arne Graue
This study focuses on the use of pressure measurements to monitor the effectiveness of foam as a CO2 mobility control agent in oil-producing reservoirs. When it is applied optimally, foam has excellent potential to improve reservoir sweep efficiency, as well as CO2 utilization and storage, during CO2 Enhanced Oil Recovery (EOR) processes. In this study, we present part of an integrated and novel workflow involving laboratory measurements, reservoir modeling and monitoring. Using the recorded bottom-hole pressure data from a CO2 foam pilot study, we demonstrate how transient pressures could be used to monitor CO2 foam development inside the reservoir. Results from a recent CO2 foam pilot study in a heterogeneous carbonate field in Permian Basin, USA, are presented. The injection pressure was used to evaluate the development of foam during various foam injection cycles. A high-resolution radial simulator was utilized to study the effect of foam on well injectivity, as well as on CO2 mobility in the reservoir during the surfactant-alternating gas (SAG) process. Transient analysis indicated constant temperature behavior during all SAG cycles. On the other hand, differential pressures consistently increased during the surfactant injection and decreased during the subsequent CO2 injection periods. Pressure buildup during the periods of surfactant injection indicated the development of a reduced mobility zone in the reservoir. The radial model proved to be useful to assess the reservoir foam strength during this pilot study. Transient analysis revealed that the differential pressures during the SAG cycles were higher than the pressures observed during the water-alternating gas (WAG) cycle which, in turn, showed foam generation and reduced CO2 mobility in the reservoir. Although pressure data are a powerful indicator of foam strength, additional measurements may be required to describe the complex physics of in situ foam generation. In this pilot study, it appeared that the reservoir foam strength was weaker than that expected in the laboratory.