Keming Liu

Dr. Keming Liu

Nanchang Institute of Technology

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
11 February 2015 in Metallurgical and Materials Transactions A
Verified
Journal Article
Closed access
PDF file
KLKeming Liu
Keming Liu
Zhengyi JiangZhengyi Jiang
Zhengyi Jiang
Jingwei ZhaoJingwei Zhao
Jingwei Zhao
JZJin Zou
Jin Zou
LLLei Lu
Lei Lu
DLDeping Lu
Deping Lu

26 October 2015 in Journal of Materials Engineering and Performance
Verified
Journal Article
Closed access
PDF file
KLKeming Liu
Keming Liu
Zhengyi JiangZhengyi Jiang
Zhengyi Jiang
HZHaitao Zhou
Haitao Zhou
DLDeping Lu
Deping Lu
Andrej AtrensAndrej Atrens
Andrej Atrens
YYYanling Yang
Yanling Yang

11 September 2013 in Journal of Materials Engineering and Performance
Verified
Journal Article
Closed access
PDF file
KLKeming Liu
Keming Liu
DLDeping Lu
Deping Lu
HZHaitao Zhou
Haitao Zhou
YYYanling Yang
Yanling Yang
Andrej AtrensAndrej Atrens
Andrej Atrens
JZJin Zou
Jin Zou

28 August 2019 in Materials
Verified
Journal Article
Open access
PDF file
WCWei Chen
Wei Chen
XHXiaona Hu
Xiaona Hu
WGWei Guo
Wei Guo
JZJin Zou
Jin Zou
KLKeming Liu
Keming Liu
DTDunqiang Tan
Dunqiang Tan
Effects of C addition on the microstructures of as-cast Cu–Fe–P (mass fraction) alloys were systematically investigated. The results show that C addition can refine the matrix microstructure and make Fe particles finer. The Fe particles observed in both the non-C-alloyed and C-alloyed specimens are α-Fe particles, which possess a body-centered cubic (bcc) structure with a Nishiyama–Wassermann orientation relationship with the matrix. C is reported to be an γ-Fe stabilizer in the literature. The reason for the difference between the phases of Fe particles observed in this study, and that reported in the literature, are finally discussed. Additionally, C addition facilitates the decomposition of the supersaturated solid solution which occurs by the simultaneous precipitation of very fine Fe particles. Such initial decomposition product has an face-centered cubic (fcc) structure with a cube-on-cube orientation relationship with the matrix.

2 December 2021 in Journal of Materials Engineering and Performance
Verified
Journal Article
Closed access
PDF file
KLKeming Liu
Keming Liu
XSXiaochun Sheng
Xiaochun Sheng
GHGuangyu He
Guangyu He
NHNingle Han
Ningle Han
MLMulin Li
Mulin Li
HHHuiming Huang
Huiming Huang

22 April 2022 in Materials
Verified
Journal Article
Open access
PDF file
KLKeming Liu
Keming Liu
XSXiaochun Sheng
Xiaochun Sheng
XLXiaolong Li
Xiaolong Li
MLMulin Li
Mulin Li
ZSZhi Shen
Zhi Shen
Andrej AtrensAndrej Atrens
Andrej Atrens
This paper investigated the influence of deep cryogenic treatments (DCT) on the tensile strength, elongation to fracture and conductivity of a deformation-processed Cu-Ni-Co-Si alloy. The tensile properties were measured using a mechanical testing machine. The conductivity was evaluated using a low-resistance tester. The microstructure and precipitated phases were analyzed using scanning electron microscopy (SEM), transmission electron microscopy (TEM), an energy dispersive spectrometer (EDS) and an X-ray diffractometer (XRD). The tensile strength, elongation to fracture and conductivity of the Cu-1.34Ni-1.02Co-0.61Si alloy before and after cold rolling at 47% reduction increased with increasing DCT time and tended to be stable at about 36 h. The microstructure became more uniform after the DCT. The grain size was refined and was smallest after DCT for 48 h. The DCT promoted the precipitation of the solid solution elements Ni, Co and Si from the Cu matrix to form many fine and evenly distributed 20–70 nm spherical second-phase particles in the grains and grain boundaries.