A low-power complex filter based on high-efficient biquad is presented under low-voltage application in this brief. In order to achieve higher shift frequency, one improved biquad is proposed to overcome the essential limitation of the original structure. It costs less power and becomes more compact compared to the Tow Thomas biquad. In order to further reduce the power consumption, an amplifier suitable for low-voltage application is employed. To overcome the variation of resistance and capacitance, a simple on-chip tuning strategy through the calibration of resistor is integrated. To validate the improved biquad, a fourth-order complex filter is fabricated in TSMC 0.13 μm standard RFCMOS technology. The measured results show that the complex filter consumes 0.5 mA with a 0.7-V power supply. It is centered at 1.65 MHz with 0.9-MHz -0.5 dB-bandwidth and the image rejection is about 18.33 dB with the voltage gain of 8.1 dB.
This paper proposes an ultra-low voltage delay element for battery-assistance DC energy harvesting systems. By inserting a low voltage level shifter (VLS), a wider voltage range is obtained to bias the body of the delay element. Thus, both the voltage transfer curve (VTC) and the DC gain of the delay element are enhanced. Due to the introduction of the VLS, the cold start-up ring oscillator constituted by the proposed delay element can achieve oscillation under an extremely low input voltage. The fully integrated cold start-up ring oscillator with 21 stages of the proposed element is implemented in a standard 180 nm complementary metal oxide semiconductor (CMOS) process. The post-layout experimental results indicate that the cold start-up ring oscillator can retain oscillation when the power supply voltage (VDD) is 24 mV under a typical corner at room temperature. The output voltage swing of the cold start-up ring oscillator based on the proposed delay element is improved by more than 55% under VDD = 40 mV compared with a stacked inverter-based cold start-up ring oscillator. Monte Carlo (MC) simulation from 100 samples shows the enhanced output swing with the proposed delay element under process variation.
This paper presents a voltage level shifter (VLS) based on two feedback loops. The complementary feedback signals in the high voltage domain are re-used to assist voltage conversion and the complementary phase in the low voltage domain is not required. Unlike the conventional VLS, which depends on the pull-up network and pull-down network to achieve level shift, the transitions of both high-to-low and low-to-high of the proposed VLS are undertaken by two different feedback loops, respectively. Implemented in a standard 180 nm CMOS process, post-layout Monte Carlo (MC) simulations from 4000 points under mismatch variation show that the dynamic power (DP) and the propagation delay (PD) of the proposed VLS are 105.3 nW and 2.0 ns, respectively, at an input voltage VIN = 0.4 V with input frequency fin = 0.1 MHz. Meanwhile, the excellent normalized standard deviation of DP and PD is obtained with the proposed scheme. The temperature range for normal operation is from −20 °C to 85 °C.
18 November 2025 in IEEE Microwave and Wireless Technology Letters
This letter proposes a fully integrated on-chip dual-band RF energy harvesting (RFEH) front-end based on 0.15-$\mu $ m pHEMT GaAs technology. To realize a flexible design of dual-band RFEH front-end, a T-shape-like impedance matching network (IMN) with two symmetric series–parallel $LC$ networks is proposed. An odd–even-mode analysis theory for symmetrical T-type IMN is introduced, enabling rapid construction of dual-band IMN. Since the frequency bands in both modes remain mutually unaffected, this approach significantly reduces dual-band iteration time. A highly efficient dual-band GaAs on-chip RFEH front-end operating at 2.4 and 5.8 GHz was fabricated with a chip area of only $700\times 700~\mu \text {m}^{2}$ . Measurements validate the RFEH front-end achieves a peak power conversion efficiency (PCE) of 64.3% and 40.8% at 2.4 and 5.8 GHz, respectively, with 19 dBm of input power level (Pin) and 2.2-k$\Omega $ load resistive (RL).