Fast start-up crystal oscillators (XOs) based on energy injection with an auxiliary oscillator (AO) are efficacious in improving the energy consumption of duty-cycled the Internet of Things (IoT) devices. Nonetheless, the frequency mismatch ( ${\Delta } {F}$ ) between the injection frequency and the crystal’s resonance frequency restrains the injection efficiency and start-up improvement. This work presents an automatic phase-error correction (APEC) technique for automatically correcting the phase error incurred due to ${\Delta } {F}$ up to $10{^{4}}$ ppm and safeguarding the XO start-up performance. An inflection detector (ID) based on a dynamic comparator (DCMP) traces the crystal resonant signal’s peak points and selects the appropriate signals for injection. We fabricated the proposed fast start-up XO in a 40-nm CMOS process. It achieves a start-up time of $17.5~{\mu }$ s with a 16-MHz crystal and a 1.0-V ${V} {_{\text {DD}}}$ . Furthermore, the start-up time only varies by ±1.42% over a ${\Delta } {F}$ of ${\pm } 10{^{4}}$ ppm, and ±4.5% amid temperature variations (−40°C to $85~{^{\circ }}$ C), evincing the robustness of the proposed technique. The power consumption and phase noise in the steady state are $84~{\mu }$ W and −139 dBc/Hz at 1-kHz offset, respectively.
This study presents a low-power Zigbee receiver with a current-reusing structure and function-reused mixing techniques. To reduce the overall power consumption, a low noise amplifier (LNA) and a power amplifier (PA) share the biasing current with a voltage-controlled oscillator (VCO) in the receiving (RX) mode and transmitting (TX) mode, respectively. The function-reused mixer reuses the radio frequency trans-conductance (RF gm) stage to amplify the down-converted intermediate frequency (IF) signal, obtaining a free IF gain without extra power consumption. A peak detector circuit detects the receiving signal strength and auto-adjusts the biasing current to save power when a strong signal strength is detected. Meanwhile, the peak detector helps to provide a coarse gain control as part of the auto-gain-control function. As part of the IF gain range is shared by the multiple-feedback (MFB) low-pass filter, the number of programmable-gain IF amplifier stages can be reduced, which also means a decrease in power consumption. A prototype of this wireless sensor network (WSN) receiver was designed and fabricated using the TSMC 130 nm CMOS process under a supply voltage of 1 V. The entire receiver realizes a noise figure (NF) of 3.5 dB and a receiving sensitivity of −90 dBm for the 0.25 Mbps offset quadrature phase shift keying (O-QPSK) signal with a power consumption of 2.9 mW.
1 January 2025 in IEEE Transactions on Instrumentation and Measurement
This paper presents a 2.4 GHz LC digitally controlled oscillator (DCO) at near-threshold supplies (0.5~0.7 V). It was a challenge to achieve a low voltage, low power, and high resolution simultaneously. DCOs with metal oxide semiconductor (MOS) varactors consume low power, but their resolution is limited. ΔΣ-DCOs can achieve a high resolution at the cost of high power consumption. A multi-stage capacitance shrinking technique was proposed in this paper to address the tradeoff mentioned above. The unit variable capacitance of the LC tank was largely reduced by the bridging capacitors and the number of stages. A current-reuse technique was used to further lower the power. Based on the above techniques, the prototype was fabricated using a 130-nm complementary MOS (CMOS) technology with multiple supplies (0.5~0.7 V for the DCO core, 1.2 V for the buffer). The measurement results showed that the phase noise at a 0.6-V supply was −126.27 dBc/Hz at 1 MHz and −125.9480 dBc/Hz at 1 MHz at the carriers of 2.4 GHz and 2.5 GHz, respectively. The best figure of merit (FoM) of 195.68 was obtained when VDD = 0.6 V. The DCO core consumed 1.1 mA at a 0.6-V supply.
31 December 2015 in International Journal of RF and Microwave Computer-Aided Engineering