Dariusz Urbaniak

Dr. Dariusz Urbaniak


Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 July 2020 in Materials
Verified
Journal Article
Open access
PDF file
Jaroslaw KrzywanskiJaroslaw Krzywanski
Jaroslaw Krzywanski
DUDariusz Urbaniak
Dariusz Urbaniak
HOHenryk Otwinowski
Henryk Otwinowski
TWTomasz Wyleciał
Tomasz Wyleciał
Marcin SosnowskiMarcin Sosnowski
Marcin Sosnowski
The milling process is a complex phenomenon dependent on various technological and material parameters. The development of a fluidized bed jet milling model is of high practical significance, since milling is utilized in many industries, and its complexity is still not sufficiently recognized. Therefore, this research aims to optimize fluidized bed jet milling with the use of fuzzy logic (FL) based approach as one of the primary artificial intelligence (AI) methods. The developed fuzzy logic model (FLMill) of the investigated process allows it to be described as a non-iterative procedure, over a wide range of operating conditions. Working air pressure, rotational speed of the classifier rotor, and time of conducting the test are considered as inputs, while mass and mean Sauter diameter of the product are defined as outputs. Several triangular and constant linguistic terms are used in the developed FLMill model, which was validated against the experimental data. The optimum working air pressure and the test’s conducting time are 500 kPa and 3000 s, respectively. The optimum rotational speed of the classifier is equal to 50 s−1, considering the mass of the grinding product, and 250 s−1 for the mean Sauter diameter of the product. Such operating parameters allow obtaining 243.3 g of grinding product with the mean Sauter diameter of 11 µm. The research proved that the use of fuzzy logic modeling as a computer-based technique of solving mechanical engineering problems allows effective optimization of the fluidized bed jet milling process.

22 December 2021 in Materials
Verified
Journal Article
Open access
PDF file
HOHenryk Otwinowski
Henryk Otwinowski
Jaroslaw KrzywanskiJaroslaw Krzywanski
Jaroslaw Krzywanski
DUDariusz Urbaniak
Dariusz Urbaniak
TWTomasz Wyleciał
Tomasz Wyleciał
Marcin SosnowskiMarcin Sosnowski
Marcin Sosnowski
Air classifier devices have a distinct advantage over other systems used to separate materials. They maximize the mill’s capacity and therefore constitute efficient methods of reducing the energy consumption of crushing and grinding operations. Since improvement in their performance is challenging, the development of an efficient modeling system is of great practical significance. The paper introduces a novel, knowledge-based classification (FLClass) system of bulk materials. A wide range of operating parameters are considered in the study: the mean mass and the Sauter mean diameter of the fed material, classifier rotor speed, working air pressure, and test conducting time. The output variables are the Sauter mean diameter and the cut size of the classification product, as well as the performance of the process. The model was successfully validated against experimental data. The maximum relative error between the measured and predicted data is lower than 9%. The presented fuzzy-logic-based approach allows an optimization study of the process to be conducted. For the considered range of input parameters, the highest performance of the classification process is equal to almost 362 g/min. To the best of our knowledge, this paper is the first one available in open literature dealing with the fuzzy logic approach in modeling the air classification process of bulk materials.

19 June 2023 in Energies
Verified
Journal Article
Open access
PDF file
DZDaniel Zbroński
Daniel Zbroński
HOHenryk Otwinowski
Henryk Otwinowski
AGAleksandra Górecka-Zbrońska
Aleksandra Górecka-Zbrońska
DUDariusz Urbaniak
Dariusz Urbaniak
TWTomasz Wyleciał
Tomasz Wyleciał
Poland, which has been a European Union member since 2004, has undertaken compliance with its commitments to increase its share in the generation of energy from renewable sources. The target set for 2020, which is to attain a share of 15 percent of the gross final consumption of energy coming from renewable sources, has been met by Poland. The new targets for 2030, incorporated in the draft the Energy Policy of Poland 2040, assume an increase to at least 23 percent of the proportion of energy obtained from renewable sources in the gross final energy consumption. On the basis of data from the Central Statistical Office, the authors of this work analysed the changes in electricity generation based on renewable energy sources. In the period of 2004–2021, it was stated that the percentages of individual renewable sources constitute 43.7% for wind energy, 35.3% for solid biofuels, 14% for hydropower, 4.2% for biogas, 2.5% for solar energy, and 0.3% for other sources (municipal waste and liquid biofuels). In addition, this work indicates the maximal relative changes in production and the maximal changes in the portion of production, in addition to the annual and periodic rate of changes in the production of these energy sources in Poland.

16 April 2021 in Materials
Verified
Journal Article
Open access
PDF file
DUDariusz Urbaniak
Dariusz Urbaniak
HOHenryk Otwinowski
Henryk Otwinowski
TWTomasz Wyleciał
Tomasz Wyleciał
ВЖВладимир /Vladimir Жуков/Zhukov
Владимир /Vladimir Жуков/Zhukov
ABAleksei Yevgenyevich Barochkin
Aleksei Yevgenyevich Barochkin
JBJarosław Boryca
Jarosław Boryca
Raw materials are used in many industrial technologies. The raw material frequently has to be prepared as an intermediate with an appropriate particle size distribution, which requires the use of grinding. In grinding processes, energy consumption is a very important profitability criterion for the applied particular size reduction technology. The paper describes the comminution process that takes place in the jet mill using a modified form of the thermodynamic theory of grinding. In this theory, new material characteristics have been added: the surface and volumetric density of grinding energy. The thermodynamic theory is a combination of the classical Kick’s theory and the modified form of Rittinger’s theory. The tested physical magnitudes are a measure of the energy consumption of the grinding process. They describe the energy that must be provided in the grinding process to overcome interactions between particles related to the volume and surface of the material. Knowledge of these magnitudes is necessary to model thermomechanical phenomena in the solid state. The paper presents the results of research on comminution in a jet mill, on the basis of which the values of the tested material magnitudes were determined. It is graphically shown how the values of the tested magnitudes depend on the grain size of the ground samples.

1 November 2024 in Materials
Verified
Journal Article
Open access
PDF file
Jaroslaw KrzywanskiJaroslaw Krzywanski
Jaroslaw Krzywanski
JBJarosław Boryca
Jarosław Boryca
DUDariusz Urbaniak
Dariusz Urbaniak
HOHenryk Otwinowski
Henryk Otwinowski
TWTomasz Wyleciał
Tomasz Wyleciał
Marcin SosnowskiMarcin Sosnowski
Marcin Sosnowski
Heating steel charges is essential for proper charge formation. At the same time, it is a highly energy-intensive process. Limiting the scale formed is critical for reducing heat consumption in this process. This paper applies fuzzy logic to model heating and scale formation in industrial re-heating furnaces. Scale formation depends on the temperature of the initial charge, heating time, excess air coefficient value, and initial scale thickness. These parameters were determined based on experimental tests, which are also the inputs in the model of the analyzed process. The research was carried out in walking beam furnaces operating in hot rolling mill departments. To minimize the excess energy consumption for heating a steel charge in an industrial furnace before forming, a heating and scale formation (HSF) model was developed using the fuzzy logic-based approach. The developed model allows for the prediction of the outputs, i.e., the charge’s final surface temperature and the scale layer’s final thickness. The comparison between the measured and calculated results shows that the model’s accuracy is acceptable.

17 July 2019 in Springer Proceedings in Energy
Verified
Book Chapter
Closed access
PDF file
DUDariusz Urbaniak
Dariusz Urbaniak
ABAgnieszka Bala-Litwiniak
Agnieszka Bala-Litwiniak
TWTomasz Wyleciał
Tomasz Wyleciał
PWPaweł Wawrzyniak
Paweł Wawrzyniak