Miroslav Spano

Miroslav Spano

orcid

Research Focus & Metrics

Academic Career Length

19Years (2008-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 October 2011 in Journal of Microbiological Methods
Verified
Journal Article
Closed access
DŠDagmar Šrůtková
Dagmar Šrůtková
AŠAlena Španova
Alena Španova
MSMiroslav Spano
Miroslav Spano
VDVladimír Dráb
Vladimír Dráb
MSMartin Schwarzer
Martin Schwarzer
BRBohuslav Rittich
Bohuslav Rittich

1 January 2016 in International Journal of Pavement Research and Technology
Verified
Journal Article
Open access
KAKarel Adam
Karel Adam
Jaromir RihaJaromir Riha
Jaromir Riha
MSMiroslav Spano
Miroslav Spano
Asphalt concrete is a traditional material used for the constructions of upstream sealing of reservoir dams, particularly in upper reservoirs of pumped storage hydroelectric plants. The asphalt layer is often exposed to significant fluctuations of temperature caused, for example, by heating the facing from the sun and by its subsequent rapid cooling by water during reservoir periodical filling. To better understand the physical phenomena and behaviour of the facing in terms of vapour diffusion, the state of stress, etc., it is necessary to know temperature phenomena in the asphalt facing. This paper describes the measurement of temperature in the asphalt facing of the Dlouhe Strane pumped storage hydroelectric plant and its evaluation using 1D numerical model of heat flow in the asphalt concrete facing. Numerical simulation for selected load scenarios enabled the temperature phenomena that take place in the construction of the asphalt-concrete facing to be quantified. The analysis shows that during insolation, the asphalt facing is exposed to the significant temperature rise on its surface and also over its whole thickness. Similarly during frost weather the facing becomes frozen in its entire thickness. During the day cycle the temperature in the asphalt layers changes significantly. However, the temperature in the underlying rockfill dam body becomes steady approximately at the depth of 1.0m

2 February 2011 in Coastal Engineering Proceedings
Verified
Journal Article
Open access
PDF file
SLStefanie Lorke
Stefanie Lorke
ABAnja Bruning
Anja Bruning
JMJentsje Van der Meer
Jentsje Van der Meer
HSHolger Schuttrumpf
Holger Schuttrumpf
ABAntje Bornschein
Antje Bornschein
Jaromir RihaJaromir Riha
Jaromir Riha
Intention of the project FlowDike-D is to quantify the impacts of current and wind on wave run-up and wave overtopping and to consider these processes in existing design formulae for estuarine, river and sea dikes. Physical model tests were carried out in the shallow water basin at DHI (Hørsholm/Denmark) for two different dike geometries (1:3 and 1:6 sloped dike). The paper introduces the model setup and test programme followed by a short description of the applied instrumentation. The test results for wave run-up and wave overtopping with oblique and non-oblique wave attack, but without current, correspond well with existing formulae from the EurOtop-Manual (2007). The influence of current parallel to the dike combined with different angles of wave attack on wave overtopping and wave run-up has been quantified. A distinction was made between wave attack with and against the current.

28 July 2015 in European Food Research and Technology
Verified
Journal Article
Closed access
PDF file
AŠAlena Španová
Alena Španová
VDVladimír Dráb
Vladimír Dráb
KTKristýna Turková
Kristýna Turková
MSMiroslav Spano
Miroslav Spano
RBRadka Burdychová
Radka Burdychová
BRBohuslav Rittich
Bohuslav Rittich

1 September 2012 in Journal of Hydrology and Hydromechanics
Verified
Journal Article
Open access
PDF file
Jaromir RihaJaromir Riha
Jaromir Riha
MSMiroslav Spano
Miroslav Spano
The Influence of Current on the Height of Wind Wave Run-Up: A comparison of experimental results with the Czech National Standard: One of the basic questions related to the safety of dikes and river levees is the size of the freeboard. One of the important parameters for freeboard design is the height of waves and wave run-up on levee slopes. Routine and standardised calculations of wave run-up deal with the freeboards of dams where wind waves originate on the still water of the reservoir. In the case of running water in streams (thereinafter only "currents") the effect of wave and current interaction on wave run-up is usually not taken into account due to the lack of reliable knowledge regarding the phenomenon. In the Czech Republic this question is topical in the case of large rivers such as the Elbe, the Vltava and the Morava. Within the framework of the projects Hydralab III and NAZV QI 92A139, hydraulic research and further analysis focused on wave run-up as a result of the combination of current and wind wave parameters were performed. The laboratory research was carried out in a hydraulic flume with a wavemaker on the right bank and a levee with a slope of 1:3 installed on the left bank opposite the wavemaker. Waves were generated both perpendicular and oblique to the levee axis; the angle of oblique wave attack varied within the range of ± 30°. The aim of this paper is to compare the results of the mentioned research with recommendations mentioned in the Czech National Standard CSN 75 0255Calculation of wave effects on water structuresand to quantify the effect of current on the wave run-up height.

30 October 2020 in Water
Verified
Journal Article
Open access
PDF file
MSMiroslav Spano
Miroslav Spano
Jaromir RihaJaromir Riha
Jaromir Riha
AŠAlena Španová
Alena Španová
OŠOndrej Šedo
Ondrej Šedo
BRBohuslav Rittich
Bohuslav Rittich
Asphalt concrete linings (ACLs) are frequently used in pumped-storage hydropower schemes with frequently oscillating reservoir water levels. ACLs can be damaged during operation, which shortens their service life. One type of damage is the formation of blisters. In this study, the bacterial diversity in damaged and undamaged portions of the ACL of an upper water reservoir was evaluated. Matrix-Assisted Laser Desorption/Ionization–Time of Flight Mass Spectrometry (MALDI-TOF MS) was employed for the identification of the bacterial strains. No bacteria were detected growing inside the undamaged dense layer. Low bacterial diversity (2 and 4 morphotypes) was found in the upper part that has no contact with the reservoir water and in the lowest part that is permanently under water, respectively. More complex bacterial diversity (16 morphotypes covered by 2 different genera and 4 species) was found on the mastic coating of the ACL, which was alternately under and above the water. Very complex bacterial compositions (53 morphotypes covered by at least 13 different species from 6 genera) were found in samples taken from open blisters. Bacterial genera that are known to utilize asphalt products as a source of nutrition were found in the open blisters. The results reflect the importance of bacterial diversity in blisters and their possible role in ACL degradation.