Yung-Lung Lee

Dr. Yung-Lung Lee

Department of Power Vehicle and Systems Engineering, Chung-Cheng Institute of Technology, National Defence University

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
3 June 2021 in Applied Sciences
Verified
Journal Article
Open access
PDF file
TYTsu-Ping Yu
Tsu-Ping Yu
Yung-Lung LeeYung-Lung Lee
Yung-Lung Lee
YLYa-We Li
Ya-We Li
SMShih-Wei MAo
Shih-Wei MAo
With the continued development of 5G mobile communications technology, the implementation of high-power communication systems has become a key indicator of developed nations. Communication modules are also trending toward wide bandwidth and high-capacity Multi-Input and Multi-Output systems. As the signal transmission speed and resolution continue with the increasing trend, the power used to operate these communications systems increase, causing extreme heat generation by transmit/receive modules (T/R module). In conditions where computation load increases in micro design systems, chips must operate in environments that are narrow, sealed, and have no convection, which can drastically increase the thermal load within a system. If no proper cooling system is utilized, the system fails or operates at impacted performance due to excessive temperatures. To solve the aforementioned problem, this study aimed to optimize the design of the cooling system in the T/R modules of communications systems by integrating heat pipes, cooling fans, cooling fins, and cooling chips within a limited space. We also proposed four types of cold plates based on the different directional clamp-in configuration methods of heat pipes within copper panels and utilized the finite element method to simulate and analyze the heat dissipation performance. The simulation results reveal that cold plates of types I and II can achieve a better heat dissipation performance. Finally, types I and II cold plates were selected for production and experimental verification. The results show that heat dissipation performances were similar to simulation results. The results also confirmed that type II cold plate has a better temperature uniformity and heat transfer efficiency. Thus, the cooling mechanism depicted in this study is viable in practical applications. The proposed mechanisms can also provide a reference for heat dissipation design patterns in different electronic module settings.
1

30 July 2021 in Applied Sciences
Verified
Journal Article
Open access
PDF file
JLJian-Yi Liang
Jian-Yi Liang
Yung-Lung LeeYung-Lung Lee
Yung-Lung Lee
SMShih-Wei MAo
Shih-Wei MAo
MTMing-Da Tsai
Ming-Da Tsai
A radar system requires a number of high-power components operating in a narrow and convection-free environment. This study aims to develop an integrated heat dissipation system that is suitable for the high-power electronic equipment of radar systems. The proposed heat dissipation mechanism integrates a fluid circulation-type cold plate with a quad transmit receive module. The finite element method in the COMSOL fluid–solid coupling heat transfer analysis software was used to analyze the heat dissipation performance of the cold plate in the proposed mechanism. The Taguchi method was adopted to optimize the cold plate design. The simulation and experimental results show that the proposed mechanism can control the temperature equalization and temperature of the system within the specified requirements. The practicality of the proposed mechanism was verified. The findings can serve as a reference for the design of high-power electronic equipment in a heat dissipation system.
1

4 September 2020 in Sensors
Verified
Journal Article
Open access
PDF file
Yung-Lung LeeYung-Lung Lee
Yung-Lung Lee
For radar systems with low update rates; such as track-while-scan (TWS) systems using rotating phased array antennas; reducing the prediction error is a very important issue. A good interacting multiple models (IMM) hybrid filter combined with circular and linear filters that are defined in relation to three measurements has been proposed in the literature. However; the algorithm requires three previous measurements; and too much prior information will result in a reduced ability to predict the future position of a highly maneuvering target. A new circular prediction algorithm for maneuvering target tracking is proposed as a non-linear prediction filter in this paper. Based on this new predictor; we also proposed a new type of IMM filter that has good estimation performance for high maneuvering targets. The proposed hybrid filter is entirely defined in relation to two measurements in a three-dimensional space to obtain a better maneuver following capability than the three measurements hybrid filter. Two target profiles are included for a comparison of the performance of our proposed scheme with that of the conventional circular; linear and IMM filters. The simulation results show that under low update rates; the proposed filter has a faster and more stable estimation response than other filters
1

1 May 2010
Verified
Conference Paper
Closed access
Yung-Lung LeeYung-Lung Lee
Yung-Lung Lee
In this work, the Input-Estimation IE algorithm based on Kalman filter F is proposed to estimate the atmospheric disturbance. It can hold a high disturbance estimating performance when system variation is unknown and under the disturbances. The input estimation algorithm is an on-line inverse estimation method that based on the F and least square method, which estimate the system disturbance without extra sensors. The estimation performance of the proposed estimator is also studied in estimating the atmospheric disturbance for the aircraft system. The simulation results shown that the proposed estimator can be a good disturbance estimator for aircraft system in estimating the atmospheric disturbance.
1