Preparation and Characterization of Glutaraldehyde-Crosslinked Kappa Carrageenan Hydrogel

The lignocellulosic residue from the palm oil industry, oil palm empty fruit bunch (OPEFB), represents a challenge to both producing industries and environment due to its disposal difficulties. Alternatively, OPEFB can be used for the production of valuable products if pretreatment methods, which overcome OPEFB recalcitrance and allow tailored valorization of all its carbohydrates and lignin, are developed. Specifically, high-value applications for lignin, to increase its contribution to the feasibility of lignocellulosic biorefineries, demand high-purity fractions. In this study, acid-catalyzed organosolv using ethanol as a solvent was used for the recovery of high-purity lignin and digestible cellulose. Factors including catalyst type and its concentration, temperature, retention time, and solid-to-liquid (S/L) ratio were found to influence lignin purity and recovery. At the best conditions (0.07% H₂SO₄, 210 °C, 90 min, and S/L ratio of 1:10), a lignin purity and recovery of 70.6 ± 4.9% and 64.94 ± 1.09%, respectively, were obtained in addition to the glucan-rich fraction. The glucan-rich fraction showed 94.06 ± 4.71% digestibility within 18 h at an enzyme loading of 30 filter paper units (FPU) /g glucan. Therefore, ethanol organosolv can be used for fractionating OPEFB into three high-quality fractions (glucan, lignin, and hemicellulosic compounds) for further tailored biorefining using low acid concentrations. Especially, the use of ethanol opens the possibility for integration of 1st and 2nd generation ethanol benefiting from the separation of high-purity lignin.

Microbubbles with slow rising speed, higher specific area and greater oxygen dissolution are desired to enhance gas/liquid mass transfer rate. Such attributes are very important to tackle challenges on the low efficiency of gas/liquid mass transfer that occurs in aerobic wastewater treatment systems or in the aquaculture industries. Many reports focus on the formation mechanisms of the microbubbles, but with less emphasis on the system optimization and assessment of the aeration efficiency. This work assesses the performance and evaluates the aeration efficiency of a porous venturi-orifice microbubble generator (MBG). The increment of stream velocity along the venturi pathway and orifice ring leads to a pressure drop (P_atm > P_abs) and subsequently to increased cavitation. The experiments were run under three conditions: various liquid velocity (Q_L) of 2.35–2.60 m/s at fixed gas velocity (Q_g) of 3 L/min; various Q_g of 1–5 L/min at fixed Q_L of 2.46 m/s; and free flowing air at variable Q_Ls. Results show that increasing liquid velocities from 2.35 to 2.60 m/s imposes higher vacuum pressure of 0.84 to 2.27 kPa. They correspond to free-flowing air at rates of 3.2–5.6 L/min. When the system was tested at constant air velocity of 3 L/min and under variable liquid velocities, the oxygen dissolution rate peaks at liquid velocity of 2.46 m/s, which also provides the highest volumetric mass transfer coefficient (K_La) of 0.041 min⁻¹ and the highest aeration efficiency of 0.287 kgO₂/kWh. Under free-flowing air, the impact of Q_L is significant at a range of 2.35 to 2.46 m/s until reaching a plateau K_La value of 0.0416 min⁻¹. The pattern of the K_La trend is mirrored by the aeration efficiency that reached the maximum value of 0.424 kgO₂/kWh. The findings on the aeration efficiency reveals that the venturi-orifice MBG can be further optimized by focusing on the trade-off between air bubble size and the air volumetric velocity to balance between the amount of available oxygen to be transferred and the rate of the oxygen transfer.