The quest for a clean, renewable and sustainable energy future has been highly sought for by the scientific community over the last four decades. Photocatalytic water splitting is a very promising technology to proffer a solution to present day environmental pollution and energy crises by generating hydrogen fuel through a “green route” without environmental pollution. Transition metal dichalcogenides (TMDCs) have outstanding properties which make them show great potential as effective co-catalysts with photocatalytic materials such as TiO2, ZnO and CdS for photocatalytic water splitting. Integration of TMDCs with a photocatalyst such as TiO2 provides novel nanohybrid composite materials with outstanding characteristics. In this review, we present the current state of research in the application of TMDCs in photocatalytic water splitting. Three main aspects which consider their properties, advances in the synthesis routes of layered TMDCs and their composites as well as their photocatalytic performances in the water splitting reaction are discussed. Finally, we raise some challenges and perspectives in their future application as materials for water-splitting photocatalysts.
Herein we report on the use of different metal precursors in the synthesis of MoSe2 nanomaterials in order to control their morphology. The use of Mo(CO)6 as the metal precursor resulted in the formation of wrinkled few-layer nanosheets, while the use of H2MoO4 as the metal precursor resulted in the formation of nanoflowers. To investigate the effect of the morphologies on their performance as catalysts in the hydrogen evolution reaction, electrochemical characterization was done using linear sweep voltammetry (LSV), cyclic voltammetry (CV), and electrical impedance spectroscopy (EIS). The MoSe2 nanoflowers were found to have superior electrochemical performance towards the hydrogen evolution reaction with a lower Tafel slope, on-set potential, and overpotential at 10 mA/cm2 compared to the wrinkled few-layer nanosheets. This was found to be due to the higher effective electrochemical surface area of the nanoflowers compared to the nanosheets which suggests a higher number of exposed edge sites in the nanoflowers.
Among the primary alcohols, ethanol is referred to as a heavy chemical due to its many applications in a variety of industries. Detection of primary alcohols can be deployed as a non-invasive method in medical diagnosis and safety measures in food processing companies. Zirconium disulphide is a novel 2D layered material with exotic features when in mono or few layers, which include fast electron transport, high carrier mobility and sizeable band gap. ZrS2 and PANI were fabricated using liquid exfoliation and chemical polymerization methods respectively. Functionalization of the conducting polyaniline with ZrS2 was done using facile sonication process. The sensor showed good sensitivities (43%, 58% and 104%) which were estimated from slopes of the linear fitted plots with fast response-recovery times of 8 s and 27 s (111 ppm); 12 s and 130 s (77 ppm); and 58 s and 88 s (58 ppm). Good reproducibility at three repeated measurements (111 ppm, 77 ppm and 58 ppm) was also observed for methanol, ethanol, and isopropanol vapours respectively. Meanwhile, the sensor displayed more linearity and sensitivity towards isopropanol compared to methanol and ethanol. The sensor showed good performance even at RH values close to 100% making it a potential alcohol breath analyser.
The need to exploit the exotic properties of ZrS 2 synthesized via colloidal means is imperative. For almost a decade now there has been no literature on the colloidal synthesis of ZrS 2 nanomaterials. Meanwhile, several publications are available on other methods of synthesis mostly chemical vapour transport (CVT) and chemical vapour deposition (CVD). The synthesized bulk material from the CVT method is further subjected to exfoliation (mechanical or liquid) to obtain mono or few‐layers of ZrS 2 . With the colloidal method, there is a possibility of the oxide being formed during the synthesis of ZrS 2 and likely destabilization of the nanomaterial after synthesis on exposure to ambient environment. In this study, both the heat up and hot injection methods were employed to fabricate various morphologies of ZrS 2 nanomaterials. The metal and sulphur precursors were dissolved in a mixture of octadecene (ODE) and oleic acid (OA); and refluxed at a temperature of 290 °C in the presence of nitrogen gas. ODE served the role of non‐coordinating solvent, while OA served as the capping agent. Nanorods, nanospheres and nanosheets were obtained from the heat up method. Meanwhile, the hot injection approach produced nanosheets and nanospheres with well noticeable hollow centres. Powder X‐ray diffractometer (PXRD) validated the formation of the ZrS 2 hexagonal phase with traces of oxides of zirconium, ZrO 2 . The peak of S2p was conspicuously absent while the Zr3d peak was well noticeable in the XPS spectra. XPS and EDS measurements confirmed the replacement of the sulphur atom by the O atom on the surface of the nanomaterials. Only one exciton peak was observed for the absorption spectra from both the heat up and hot injection methods; and thermal thermogravimetry analysis (TGA) revealed three plateaux of decomposition of the nanomaterials.
A one-step colloidal synthesis of hierarchical nanoflowers of WS2 is reported. The nanoflowers were used to fabricate a chemical sensor for the detection of ammonia vapors at room temperature. The gas sensing performance of the WS2 nanoflowers was measured using an in-house custom-made gas chamber. SEM analysis revealed that the nanoflowers were made up of petals and that the nanoflowers self-assembled to form hierarchical structures. Meanwhile, TEM showed the exposed edges of the petals that make up the nanoflower. A band gap of 1.98 eV confirmed a transition from indirect-to-direct band gap as well as a reduction in the number of layers of the WS2 nanoflowers. The formation of WS2 was confirmed by XPS and XRD with traces of the oxide phase, WO3. XPS analysis also confirmed the successful capping of the nanoflowers. The WS2 nanoflowers exhibited a good response and selectivity for ammonia.
A set of three sensors based only on oleylamine capped tungsten disulphide nanoflowers was developed to discriminate between vapours of ammonia and volatile organic compounds at room temperature. The petals disassembled gradually because of reaction time manipulation during colloidal synthesis. It is these slight changes in the morphology that brought about different responses by the sensors upon exposure to the various chemical vapours. The responses of the sensors were used in the tristimulus analysis to find a pattern (fingerprint) for each target analyte making identification possible. These results present a step in the right direction towards overcoming the low specificity disadvantage associated with the chemical sensors thereby increasing their spectrum of possible applications.