This study investigates the influence of temperature and loading rate on the Mode I and Mode II interlaminar fracture behavior of carbon-nanotubes-enhanced carbon-fiber-reinforced polymer (CNT-CFRP). CNT-induced toughening of the epoxy matrix is characterized by producing CFRP with varying loading of CNT areal density. CNT-CFRP samples were subjected to varying loading rates and testing temperatures. Fracture surfaces of CNT-CFRP were analyzed using scanning electron microscopy (SEM) imaging. Mode I and Mode II interlaminar fracture toughness increased with increasing amount of CNT to an optimum value of 1 g/m2, then decreased at higher CNT amounts. Moreover, it was found that CNT-CFRP fracture toughness increased linearly with the loading rate in Mode I and Mode II. On the other hand, different responses to changing temperature were observed; Mode I fracture toughness increased when elevating the temperature, while Mode II fracture toughness increased with increasing up to room temperature and decreased at higher temperatures.
Simulating the mechanical behavior of rubbers is widely performed with hyperelastic material models by determining their parameters. Traditionally, several loading modes, namely uniaxial tensile, planar equibiaxial, and volumetric, are considered to identify hyperelastic material models. This procedure is mainly used to determine hyperelastic material parameters accurately. On the contrary, using reverse engineering approaches, iterative finite element analyses, artificial neural networks, and virtual field methods to identify hyperelastic material parameters can provide accurate results that require no coupon material testing. In the current study, hyperelastic material parameters of selected rubbers (neoprene, silicone, and natural rubbers) were determined using an artificial neural network (ANN) model. Finite element analyses of O-ring tension and O-ring compression were simulated to create a data set to train the ANN model. Then, the ANN model was employed to identify the hyperelastic material parameters of the selected rubbers. Our study demonstrated that hyperelastic material parameters of any rubbers could be obtained directly from component experimental data without performing coupon tests.
29 September 2023 in Journal of the Mechanical Behavior of Biomedical Materials
Elastomers exhibit a complex response to high-strain-rate deformation due to their viscoelastic behaviour. Environmental conditions highly impact this behaviour, especially when both temperature and humidity change. In several applications where elastomers are used, the quantity of real humidity might vary, especially when the temperature is elevated. In the current research, elastomeric materials were subjected to high-strain-rate compression in various elevated and lowered (cold) temperatures. Different humidity levels were applied at room and elevated temperatures to analyze the behaviour of rubbers in dry and moist conditions. Results showed that the mechanical behaviour of rubbers is highly affected by any environmental change. In particular, the impact caused by humidity variations is relative to their ability to absorb or repel water on their surface.
Fabricating helical scaffolds using electrospinning is a common approach for cardiac implantation, aiming to achieve properties similar to native tissue. However, this process requires multiple experimental attempts to select suitable electrospun properties and validate resulting mechanical responses. To overcome the time and cost constraints associated with this iterative procedure, Finite Element Analysis (FEA) can be applied using stable hyperelastic and viscoelastic models that describe the response of electrospun scaffolds under different conditions. In this study, we aim to create accurate simulations of the viscoelastic behavior of electrospun helical scaffolds. We fabricated helical fibers from Poly (3-caprolactone) (PCL) using the electrospinning process to achieve this. The electrospun samples were subjected to uniaxial deformation, and their response was modelled using existing hyperelastic and stress relaxation models. The simulations were built on experimental data for specific deformation speed and maximum strain conditions. The FEM results were evaluated by accounting for the stress-softening phenomenon, which significantly impacted the models. The electrospun scaffolds’ predictions were performed in other than the initial experimental conditions to verify our simulations’ accuracy and reliability.
For viscoelastic materials, the relationship between stress and strain depends on time, where the applied strain (or stress) can be expressed as a step function of time. In the present work, we investigated two temporary effects in the response of viscoelastic materials when a given strain is applied and then removed. The application of strain causes a stress response over time, also known as relaxation. By contrast, recovery is the response that occurs following the removal of an applied stress or strain. Both stress and relaxation constitute transient stages of a viscoelastic material exposed to a permanent force. In the current work, we performed several experimental tests to record the recovery in response to the total or partial removal of the strain. By observing and analyzing the mechanical response of the material to strain, we deduced that recovery is a procedure not only related to creep but also to relaxation. Hence, we created a model that simulates the behavior of viscoelastic materials, contributing to the prediction of relevant results concerning different conditions.