Burak Yenigun

Dr. Burak Yenigun

orcid

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
25 May 2023 in Nanomaterials
Verified
Journal Article
Open access
PDF file
BYBurak Yenigun
Burak Yenigun
MCMuhammad Salman Chaudhry
Muhammad Salman Chaudhry
EGElli Gkouti
Elli Gkouti
Aleksander CzekanskiAleksander Czekanski
Aleksander Czekanski
This study investigates the influence of temperature and loading rate on the Mode I and Mode II interlaminar fracture behavior of carbon-nanotubes-enhanced carbon-fiber-reinforced polymer (CNT-CFRP). CNT-induced toughening of the epoxy matrix is characterized by producing CFRP with varying loading of CNT areal density. CNT-CFRP samples were subjected to varying loading rates and testing temperatures. Fracture surfaces of CNT-CFRP were analyzed using scanning electron microscopy (SEM) imaging. Mode I and Mode II interlaminar fracture toughness increased with increasing amount of CNT to an optimum value of 1 g/m2, then decreased at higher CNT amounts. Moreover, it was found that CNT-CFRP fracture toughness increased linearly with the loading rate in Mode I and Mode II. On the other hand, different responses to changing temperature were observed; Mode I fracture toughness increased when elevating the temperature, while Mode II fracture toughness increased with increasing up to room temperature and decreased at higher temperatures.

2 January 2021 in Journal of the Brazilian Society of Mechanical Sciences and Engineering
Verified
Journal Article
Closed access
PDF file
BYBurak Yenigun
Burak Yenigun
EKErol Kilickap
Erol Kilickap

9 December 2022 in Materials
Verified
Journal Article
Open access
PDF file
BYBurak Yenigun
Burak Yenigun
EGElli Gkouti
Elli Gkouti
GBGabriele Barbaraci
Gabriele Barbaraci
Aleksander CzekanskiAleksander Czekanski
Aleksander Czekanski
Simulating the mechanical behavior of rubbers is widely performed with hyperelastic material models by determining their parameters. Traditionally, several loading modes, namely uniaxial tensile, planar equibiaxial, and volumetric, are considered to identify hyperelastic material models. This procedure is mainly used to determine hyperelastic material parameters accurately. On the contrary, using reverse engineering approaches, iterative finite element analyses, artificial neural networks, and virtual field methods to identify hyperelastic material parameters can provide accurate results that require no coupon material testing. In the current study, hyperelastic material parameters of selected rubbers (neoprene, silicone, and natural rubbers) were determined using an artificial neural network (ANN) model. Finite element analyses of O-ring tension and O-ring compression were simulated to create a data set to train the ANN model. Then, the ANN model was employed to identify the hyperelastic material parameters of the selected rubbers. Our study demonstrated that hyperelastic material parameters of any rubbers could be obtained directly from component experimental data without performing coupon tests.

2 April 2018 in Applied Sciences
Verified
Journal Article
Open access
PDF file
BYBurak Yenigun
Burak Yenigun
EKErol Kilickap
Erol Kilickap
The application areas of carbon fiber reinforced plastics (CFRP) have been increasing day by day. The machining of CFRP with incorrect machining parameters leads in huge loss cost and time. Therefore, it is very important that the composite materials are machined with correct machining parameters. The aim of this paper is to examine the influence of drilling parameters on tensile load after drilling of CFRP. The drilling operations were carried out on Computer Numerical Control (CNC) by Tungsten Carbide (WC), High Speed Steel (HSS) and Brad Spur type drill bits with spindle speeds of 1000, 3000 and 5000 rpm and feed rates of 0.05, 0.10 and 0.15 mm/rev. The results indicate that the surface roughness, delamination and thrust force, were affected by drilling parameters therefore tensile load was also affected by the same parameters. It was observed that increase in surface roughness, delamination and thrust force all lead to the decrease of tensile load of CFRP. If the correct drilling parameters are selected; the decrease in tensile load of CFRP can be saved up to 25%. Furthermore, an artificial neural network (ANN) model has been used to predict of tensile load. The results of the ANN model are in close agreement with the experimental results.

10 November 2022 in Materials
Verified
Journal Article
Open access
PDF file
EGElli Gkouti
Elli Gkouti
MCMuhammad Salman Chaudhry
Muhammad Salman Chaudhry
BYBurak Yenigun
Burak Yenigun
Aleksander CzekanskiAleksander Czekanski
Aleksander Czekanski
Elastomers exhibit a complex response to high-strain-rate deformation due to their viscoelastic behaviour. Environmental conditions highly impact this behaviour, especially when both temperature and humidity change. In several applications where elastomers are used, the quantity of real humidity might vary, especially when the temperature is elevated. In the current research, elastomeric materials were subjected to high-strain-rate compression in various elevated and lowered (cold) temperatures. Different humidity levels were applied at room and elevated temperatures to analyze the behaviour of rubbers in dry and moist conditions. Results showed that the mechanical behaviour of rubbers is highly affected by any environmental change. In particular, the impact caused by humidity variations is relative to their ability to absorb or repel water on their surface.

2 December 2019 in Materials Testing
Verified
Journal Article
Closed access
MKMusa Kilic
Musa Kilic
BYBurak Yenigun
Burak Yenigun
SBSerkan Bati
Serkan Bati
ZBZulkuf Balalan
Zulkuf Balalan
IKIhsan Kirik
Ihsan Kirik
The focus of the study is on the effect of copper addition on the porosity, microstructure and mechanical properties of hot pressed NiTi and NiTiCu shape memory alloys (SMAs), ignited by means of self-propagating high-temperature synthesis (SHS). Optical microscopy, scanning electron microscopy (SEM), X-ray diffraction (XRD), energy dispersive spectrometry (EDS), hardness tests and compression tests were applied respectively to determine the microstructure and mechanical behavior of the samples. The experimental results show that the addition of Cu into NiTi SMAs increases porosity and microhardness but also reduces compressive strength.