In September 2018, photogrammetric images and terrestrial laser scans were carried out as part of a measurement campaign for the three-dimensional recording of several historic churches in Tbilisi (Georgia). The aim was the complete spatial reconstruction with a spatial resolution and accuracy of approx. 1 cm under partly difficult external conditions, which required the use of different measurement techniques. The local measurement data were collected by two laser scanning campaigns (Leica BLK360 and Faro Focus 3D X330), several UAV flights and two terrestrial image sets. The photogrammetric point clouds were calculated with the image-based modelling programs AgiSoft and RealityCapture taking into account the control points from the laser scans. The mean residual errors from the registrations or photogrammetric evaluations are 4–16 mm, depending on the selected software, size and complexity of the monument and environmental conditions. The best completeness and quality of the resulting 3D model was achieved by using laser scan data and images simultaneously. The article presents recent results obtained with RealityCapture and gives a critical analysis of accuracy and modelling quality.

Camera calibration via bundle adjustment is a well-established standard procedure in single-medium photogrammetry. When using standard software and applying the collinearity equations in multimedia photogrammetry, the effects of refractive interfaces are compensated in an implicit form, hence by the usual parameters of interior orientation. This contribution analyses different calibration strategies for planar bundle-invariant interfaces. To evaluate the effects of implicitly modelling the refractive effects within bundle adjustment, synthetic error-free datasets are simulated. The behaviour of interior, exterior, and relative orientation parameters is analysed using synthetic datasets free of underwater imaging effects. A shift of the camera positions of 0.2% of the acquisition distance along the optical axis can be observed. The relative orientation of a stereo camera shows systematic effects when the angle of convergence varies. The stereo baseline increases by 1% at 25° convergence. Furthermore, the interface is set up at different distances to the camera. When the interface is at 50% distance assuming a parallel camera setup, the stereo baseline also increases by 1%. It becomes clear that in most cases the implicit modelling is not suitable for multimedia photogrammetry due to geometrical errors (scaling) and absolute positioning errors. Explicit modelling of the refractive interfaces is implemented into a bundle adjustment and is also used to analyse calibration parameters and deviations in object space. Real experiments show that it is difficult to separate the effects of implicit modelling, since other effects, such as poor image measurements, affect the final result. However, trends can be seen, and deviations are quantified.

The design of rotor blades is based on information about aerodynamic phenomena. An important one is fluid-structure interaction (FSI) which describes the interaction between a flexible object (rotor blade) and the surrounding fluid (wind). However, the acquisition of FSI is complex, and only a few practical concepts are known. This paper presents a measurement setup to acquire real information about the FSI of rotating wind turbines in wind tunnel experiments. The setup consists of two optical measurement systems to simultaneously record fluid (PIV system) and deformation (photogrammetry system) information in one global coordinate system. Techniques to combine both systems temporally and spatially are discussed in this paper. Furthermore, the successful application is shown by several experiments. Here, different wind conditions are applied. The experiments show that the new setup can acquire high-quality area-based information about fluid and deformation.

In dense stereo matching applications surface reflections may lead to incorrect measurements and blunders in the resulting point cloud. To overcome the problem of disturbing reflexions polarising filters can be mounted on the camera lens and light source. Reflections in the images can be suppressed by crossing the polarising direction of the filters leading to homogeneous illuminated images and better matching results. However, the filter may influence the camera’s orientation parameters as well as the measuring accuracy. To quantify these effects, a calibration and an accuracy analysis is conducted within a spatial test arrangement according to the German guideline VDI/VDE 2634.1 (2002) using a DSLR with and without polarising filter. In a second test, the interior orientation is analysed in more detail. The results do not show significant changes of the measuring accuracy in object space and only very small changes of the interior orientation (Δc ≤ 4 μm) with the polarising filter in use. Since in medical applications many tiny reflections are present and impede robust surface measurements, a prototypic trinocular endoscope is equipped with polarising technique. The interior and relative orientation is determined and analysed. The advantage of the polarising technique for medical image matching is shown in an experiment with a moistened pig kidney. The accuracy and completeness of the resulting point cloud can be improved clearly when using polarising filters. Furthermore, an accuracy analysis using a laser triangulation system is performed and the special reflection properties of metallic surfaces are presented.