The corrosion fatigue properties and fracture characteristics of friction stir welding joints of 7075 aluminum alloys were studied via corrosion fatigue tests, electrochemical measurements, and corrosion fatigue morphology and microstructure observations. The results show that the corrosion fatigue crack of the friction stir welding (FSW) joint of 7075 aluminum alloys originated in the junction zone between the thermomechanically affected zone and the weld nugget zone. The corrosion fatigue life of the joint decreased with increasing stress amplitude, with an S–N curve equation of lgN = 5.845 − 0.014S. Multiple crack sources were observed in the corrosion fatigue fracture. The main crack source originated from the corrosion pits at the interface between the thermomechanically affected zone and the weld nugget zone due to the influence of the coarse microstructure and the large potential difference between both zones. Corrosion morphologies of a rock candy block and an ant nest appeared in the crack propagation zone and the grain boundary of the weld nugget zone. In addition, fatigue speckles and intergranular fractures were observed, as well as brittle fracture characterized by cleavage steps and secondary cracks in the final fracture zone.
28 January 2021 in Journal of Central South University
The area of interest (AOI) reflects the degree of attention of a driver while driving. The division of AOI is visual characteristic analysis required in both real vehicle tests and simulated driving scenarios. Some key eye tracking parameters and their transformations can only be obtained after the division of AOI. In this study, 9 experienced and 7 novice drivers participated in real vehicle driving tests. They were asked to drive along a freeway section and a highway section, wearing the Dikablis eye tracking device. On average, 8132 fixation points for each driver were extracted. After coordinate conversion, the MSAP (Mean Shift Affinity Propagation) method is proposed to classify the distribution of fixation points into a circle type and a rectangle type. Experienced drivers’ fixation behavior falls into the circle type, in which fixation points are concentrated. Novice drivers’ fixation points, which are decentralized, are illustrated in the rectangle type. In the clustering algorithm, the damping coefficient λ determines the algorithm convergence, and the deviation parameter p mainly affects the number of clusters, where larger p values generate more clusters. This study not only provides the cluster type and cluster counts, but also presents the borderlines for each cluster. The findings provide significant contribution to eye tracking research.
Steel–tube composite structures contain multiple tubular components under tension. The enhancement of the mechanical properties of tubes under ultimate operating conditions is crucial for improving structural safety. In this study, 110 pieces of 304 stainless steel thin-walled tubes (SSTWTs) under five internal support conditions are investigated. The ultimate tensile strength, ultimate extension, and fracture energy of different groups of specimens are measured to understand the variation mechanism of fracture modes. The elastic modulus of tube filler is treated as a variable to establish a uniaxial tensile fracture matrix of 304 SSTWTs with different tube fillers and loading rates. The results demonstrate that flexible tube fillers can effectively limit the lateral necking of 304 SSTWTs. Under the middle fracture mode, the maximum increments in the ultimate strength, extension, and fracture energy of tubes are 10.81%, 24.56%, and 35.94%, respectively. Furthermore, as the support rigidity increases, the ultimate strength exhibits an overall increasing trend, while the extension and fracture energy initially increase and then decrease. Overall, this study provides a novel route for enhancing the performance of steel–tube composite structures under ultimate loading conditions, which is of great significance for improving the safety of the structural design and reducing the engineering construction cost.
A unique fiber-reinforced polymer (FRP)–aluminum spatial truss structure with upper I-type, transverse beam braces was developed for deployable bridging, yielding the operational advantages of bestraddled erection bridges. Experimental testing and numerical simulation were performed to evaluate the torsional rigidity of a fabricated cantilever, full-scale experimental structure. The predictions obtained based on a computational finite element model were strongly consistent with the experimental results. Moreover, a numerical decomposition and reconstruction procedure was employed to understand the load-bearing mechanism of the structure. The results demonstrated that the improved transverse braces possessed adequate capacity for providing sufficient rigidity and lateral stability to the complete twin-treadway structure under torsion. The torsional center of the improved structure was located at the axis of symmetry of the twin-treadway bridge deck. The representative torsional rigidity of the twin-treadway module was approximately 87.5 kN·m2/degree. Compared to the original construction, the improved structure exhibited only minor discrepancies regarding the torsional rigidity, and consistent characteristics in terms of the load-bearing mechanism. The torsional rigidity of the improved twin-treadway structure was primarily generated by the vertical bending rigidities of its two parallel single treadways through the rigid transverse braces. This significant finding specifically pertains to the unique twin-treadway hybrid bridge. The results presented in this work are expected to provide valuable insights, which could, in turn, lead to further the development of similar lightweight structural systems.