The paper presents a Switched-Capacitor Boost DC-DC Converter (SC-BC) which can be used in energy harvesting applications using thermoelectric generators (TEGs) with low output voltage, low power and a significant internal resistance. It consists of a switching capacitor circuit, where MOSFETs are used as switches, and a boost stage. The converter is a modification of a previously presented scheme in which diodes are used in the switched capacitor stage. A higher voltage gain and an increased efficiency can thus be achieved. The model of the converter was developed considering the internal resistance of the TEG and boost stage inductor. A comparison with the diode based converter is shown, with consideration of the TEG internal resistance. Calculation is presented of the main passive components. A control algorithm is also proposed and evaluated. It is based on a linearization approach, and designed for output voltage and inductor current control. The operation of both converter and control are verified with the simulation and experimental results.
This paper presents a current sensing principle appropriate for use in power electronics’ converters. This current measurement principle has been developed for metal oxide semiconductor field effect transistor (MOS-FET) and is based on UDS voltage measurement. In practice, shunt resistors and Hall effect sensors are usually used for these purposes, but the presented principle has many advantages. There is no need for additional circuit elements within high current paths, causing parasitic inductances and increased production complexity. The temperature dependence of MOS-FETs conductive resistance RDS−ON is considered in order to achieve the appropriate measurement accuracy. The “MOS-FET sensor” is also accompanied by a signal acquisition electronics circuit with an appropriate frequency bandwidth. The obtained analogue signal is therefore interposed to an A-D converter for further data acquisition. In order to achieve sufficient accuracy, a temperature compensation and appropriate approximation is used (RDS−ON = RDS−ON(Vj)). The MOS-FET sensor is calibrated according to a reference sensor based on the Hall-effect principle. The program algorithm is executed on 32-bit ARM M4 MCU, STM32F407.
Power-hardware-in-the-loop systems enable testing of power converters for electric vehicles (EV) without the use of real physical components. Battery emulation is one example of such a system, demanding the use of bidirectional power flow, a wide output voltage range and high current swings. A multiphase synchronous DC-DC converter is appropriate to handle all of these requirements. The control of the multiphase converter needs to make sure that the current is shared equally between phases. It is preferred that the closed-loop dynamic model is linear in a wide range of output currents and voltages, where parameter variations, control signal limits, dead time effects, and so on, are compensated for. In the case presented in this paper, a cascade control structure was used with inner sliding mode control for phase currents. For the outer voltage loop, a proportional controller with output current feedforward compensation was used. Disturbance observers were used in current loops and in the voltage loop to compensate mismatches between the model and the real circuit. The tuning rules are proposed for all loops and observers, to simplify the design and assure operation without saturation of control signals, that is, duty cycle and inductor current reference. By using the proposed control algorithms and tuning rules, a linear reduced order system model was devised, which is valid for the entire operational range of the converter. The operation was verified on a prototype 4-phase synchronous DC-DC converter.
Modern systems are becoming ever more complex and, thus, the possibility of failures in their operation is also growing. The complexity makes it practically impossible to make the hardware and software error-free without the special effort invested in the design process. Recently, a design methodology with the objective to avoid unacceptable risk of physical injury or of damage to the health of people, named Functional Safety, has been gaining importance. The paper presents the basics of the design process to be applied for the development of electrical / electronic / programmable electronic devices to be applied in safety critical applications.
This paper deals with an emulation system for Power Electronics Converters (PEC). The emulation of PECs is performed on a Field-Programmable Gate Array (FPGA) capable of hard real-time operation. To obtain such a system, the converter operation is described using a differential equations-based model designed with the graph theory. Differential equation coefficients are changed according to the type of converter and pulse-width modulation (PWM) signals. The tie-set and incidence matrix approach for the converter modelling is performed to describe the converter operation in a general way. Such approach enables that any type of PECs can be described appropriately. The emulator was verified experimentally by synchronous operation with a real DC-AC converter built for this purposes.