Ajay Maurya

Mr. Ajay Maurya

National Institute of Technology Patna

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
5 June 2022 in Advances in Materials and Processing Technologies
Verified
Journal Article
Closed access
Ajay MauryaAjay Maurya
Ajay Maurya
AKAmit Kumar
Amit Kumar
DMLS fabricated IN718 alloy samples with various build orientations are analysed with heat-treatment dependent mechanical and microstructural properties. The multiple heating and cooling cycles formed a complex micro-heterogeneous microstructure composed of columnar and equiaxed subgrains in the alloy. Solution treatment resulted in a partially dissolved δ phase, and the metastable γ” phase while ageing treatment eliminated the dendritic substructure. In contrast, δ-phases precipitated mainly in the interdendritic regions, and significantly eliminated the micro-segregation and Laves phases in the γ matrix after homogenised (HSA). . The tensile test showed that tensile strength decreased with increasing building orientation but ductility increased. Heat-treatment significantly improved the microhardness, ultimate tensile strength, and yield strength compared to the as-fabricated samples, but their ductility decreased. The tensile properties recorded an improvement of nearly 31.32% as compared to 0° as-built and 0° heat-treated direct aged samples. The higher microhardness (507.25 HV) was observed for the direct aged 0° build samples. The microhardness values were increased by nearly 45% after heat-treatment comparing to as-build 0° and 0° DA treated samples. The density was observed to be about 99.52% of the as-built samples, but performing the heat-treatment, no significant improvement in the density was observed and it was found similar to the as-fabricated sample.

1 January 2023 in Manufacturing Technology Today (MTT)
Verified
Journal Article
Open access
PDF file
Ajay MauryaAjay Maurya
Ajay Maurya
AKAmit Kumar
Amit Kumar
SSSurendra Kumar Saini
Surendra Kumar Saini
Christ Prakash PaulChrist Prakash Paul
Christ Prakash Paul
Laser directed energy deposition is an additive manufacturing process in which laser melted powder deposited at target spot. In the past few years, it has become more popular because it lets manufacturers make complex parts in small batches with a small number of post-processing steps. Fabrication of components in directed energy deposition takes lots of time. Therefore, it is necessary to study the build rate in laser directed energy deposition method. Optimum values of different powder feed rate, scan speed, and laser power on build rate are evaluated. It observed that the laser power is a significant process parameter in build rate followed by scan speed and powder feed rate for the printing of Inconel 718.


1 January 2025 in ASEAN Journal on Science and Technology for Development
Verified
Journal Article
Open access
PDF file
Ajay MauryaAjay Maurya
Ajay Maurya
AKAmit Kumar
Amit Kumar
SSSwarnambuj Suman
Swarnambuj Suman
The additive manufacturing (AM) technique “Direct Metal Laser Sintering (DMLS)” is used to create 3D objects directly from 3D design data. A lightweight and complexity-free part without any expensive tooling can be fabricated easily using this method, but it is still challenging to achieve the desired mechanical strength from AM parts, as the mechanical properties of AM-produced parts vary with orientation, scan strategy, and process parameters. Inconel 718 alloy is most commonly utilized in the aerospace and automotive industries, because of its high resistance to corrosion and excellent mechanical qualities. This work presents a study to investigate the orientation-based mechanical behaviour of the AM-produced Inconel 718 alloy. Samples were fabricated in three building directions: horizontal (0o), inclined (45o), and vertical (90o). Tensile tests and fractography were performed. It was observed that a 0o build produces almost 6.2% higher tensile strength and approximately 6.69% higher elongation than a 90o build sample. Also, all the samples observed ductile failure with an elongation of more than 35%.